List the flows of mass and energy located in there ChimneyGaspurifierGypsumAshseparatorFlyashFlue gasCoalsiloCoalgrinderOilAirFIGURE 1.2 Schematic diagram of a steam power plant.SteamdrumSlagPumpTurbineHHeatexchangerGeneratorPowergridDistrictheating|||

Answered: Image /qna-images/answer/cadcb21e-a08b-4d5b-b96f-0207da7535bf.jpg

Answered: Chimney Gas purifier Gypsum Ash…

Chimney Gas purifier Gypsum Ash separator Fly ash Flue gas Coal silo Coal grinder Oil Steam drum Pump Turbine Heat exchanger Generator Power grid District heating с ←

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Plsss show the details of your solution with correct pv and ts diagrams and unit analysis. Thanksss! ❤️
Pls answer thank you! The following data were obtained during performance test with a simple open cycle gas turbine engine: compressor inlet temperature, 520*R: compressor isentropic discharge temperature, 672"R: actual compressor discharge temperature, 691"R: turbine inlet temperature, 1500 R: turbine isentropic discharge temperature. 1184"R: and turbine actual discharge temperature, 1216°R. For these conditions calculate the thermal efficiency in percent.
Q4// Answer A or B 201u, 4017 All What is the final part of the flue gas way of boiler furnace found to raise the temperature of water? Explain this?. Also, demonstrate briefly the water movement in power plant? B// What are the types of feedwater heaters in power plant, compare them? Explain the methods of cooling by these heaters and the ways of feeding.
Write legibly, provide manual step by step solution, and diagram for below given problem. A superheat steam Rankine cycle has turbine inlet conditions of 17.5 Mpa and 530 C expands in a turbine to 0.007Mpa. The turbine and pumps polytropic efficiencies are 0.9 and 0.7 respectively, pressure losses between pump and turbine are 1.5MPa. What should be the pump work in KJ/kg? A. 17.3 C. 37.3 B. 27.3 D. 43.4
Specific Instruction: i.Drawaschematic diagramof each problem with labels of states of a substance;ii.For uniformity purposes, assign STATE 1 at the inlet of ahigh-pressure turbine.The states must be arranged in a chronologicalorder;iii.Ploteach cycle in a t-s diagramwith the states consistentto the states assignment in the schematic diagram;iv.Show a detailed solution 1.Consider a 200-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 8MPa and 400 0C and is cooled in the condenser at a pressure of 10 kPa. Determine (a) the quality of the steam at the turbine exit, and (b)themass flow rate of the steam.
A gas turbine cycle is preferred over steam power plant in power station that is used to generate electricity. Your manger asked you to investigate and study the possibility of upgrading the power plant discussed in Project-1 to a gas turbine cycle or a combination of both cycles (Combined cycle). The head of the department asked you to deliver a report showing a professional evaluation and assessment for gas turbine cycle efficiency given the following information.First you selected a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications:• A pressure ratio of 10.• Heat is added to the cycle at a rate of 500 kW• Air passes through the engine at a rate of 1 kg/s• The air at the beginning of the compression is at 70 kPa and 0 C.
| As a mechanical engineering technician, you are asked by your building manager to investigate the performance of a steam turbine at the main university building. Criticaly compare how heat transfer efficiency will affect the lifetime of the turbine.
Q3/a steam power plant of a 25-MW electric output power has a medium water tube steam generator of the following specifications Steam production Steam pressure Steam temperature Dryness fraction of steam in the steam drum Feed water temperature from F.W.Hs Water leaving economizer Fuel :natural gas of heating value Fuel consumption Percent of unburned fuel Flue gas flow rate Flue gas temperature Flue gas specific heat 31.6kg/s 60bar 500 °C 0.96 100 °C 250°C 38700 kJ/m 2.85 m³/s 3% 22.67%) 12.8 kg/s 150°C 1.008 kJ/kg.K 30°C Ambient temperature 1. Determine the boiler efficiency and the equivalent evaporation. 2. Draw the heat balance sheet for the boiler(all in kW). 3. Determine the overall efficiency for this plant. Answ(86%,14.75kg steam/m3 fud, Ece-19908kW, E-52835kW, Ep 22050kW, Eest-1548.3kW,
Provide a long answer using necessary graphs / equations. Describe the Rankine thermodynamic cycle. What thermodynamic processes occurs? Where is the cycle used? How to improve the cycle?
Exercise: Steam Mass Balance Fill the steam mass flow Boiler Feed Water (BFW) of the yellow parts Boiler 1 Boiler 2 100 A Fuel 50 To process HPS 50 50 10 10 Back pressure turbine Extraction G Extraction Letdown Turbine Turbine 20 20 20 10 D WHB MPS To process E В Back pressure Condensing turbine Letdown turbine 40 To process LPS vent V cw O cw Deareator From process Condensate If the MPS demand is 20t/h less than the current supply, how to adjust the steam system? Water Make up 35 Treatment fresh water
please answer a question bartleby !!!
A Simple Rankine cycle works befween pressures 38 bew 38 bar anod la bar, bhe instial cotkibion of the cycle eppieiency, uorks vabo and speeipic stéam eansumption. steam beang odry saburtaech, Calau tabe 38 bar 子 lo ber