Check my we When measuring small pressure differences with a manometer, often one arm of the manometer is inclined to improve the accuracy of reading. (The pressure difference is still proportional to the vertical distance and not the actual length of the fluid along the tube) The air pressure in a circular duct is to be measured using a manometer whose open arm is inclined 45° from the horizontal, as shown in the figure The density of the liquid in the manometer is 0.79 kg/L and the vertical distance between the fluid levels in the two arms of the manometer is 12 cm. Determine the gage pressure of air in the duct and the length of the fluid column in the inclined arm above the fluid level in the vertical arm.

Check my we When measuring small pressure differences with a manometer, often one arm of the manometer is inclined to improve the accuracy of reading. (The pressure difference is still proportional to the vertical distance and not the actual length of the fluid along the tube) The air pressure in a circular duct is to be measured using a manometer whose open arm is inclined 45° from the horizontal, as shown in the figure The density of the liquid in the manometer is 0.79 kg/L and the vertical distance between the fluid levels in the two arms of the manometer is 12 cm. Determine the gage pressure of air in the duct and the length of the fluid column in the inclined arm above the fluid level in the vertical arm.

Name: Check my weWhen measuring small pressure differences with a manometer
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Check my weWhen measuring small pressure differences with a manometer, often one arm of the manometer is inclined to improve the accuracy ofreading. (The pressure difference is still proportional to the vertical distance and not the actual length of

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The fluid in a manometer tube is 60 % water and 40 % alcohol (S.G. = 0.83). What is the manometer fluid height difference (in ft) if a 13.6 psi pressure is applied across the two ends of a manometer?
A cylinder is filled with 0.4m3 of air at a pressure of 6bar The cylinder is compressed to 0.1 m.3. What is the resulting absolute pressure? Convert p1 to absolute pressure.
Installed in tank, X are pressure gauges A and B and tank Y are pressure gauges C and D as shown in the figure. The reading at gauges B and C are 90 kPa and 20 kPa vacuum respectively. Determine the readings in gauges A and D actual pressure of air inside tank X and Y. Atmospheric pressure is 1bar. Expressed all answers in kPa.
Q2. a. Gauge (G) and mercury manometric (MM) tensiometers was were installed at 30 and 100cm respectively below the soil surface. The distance from the gauge to center of the ceramic cup is 50cm and from the mercury level in the reservoir to soil surface is 30 cm. Reading for the G. tensoimeter was - 61kP(kilopascals) and for the height of the mercury level in the MM tensiometer was -55KP Answer the following: 1. calculate the matric potential of the GT and MMT 2. Find the total potential of GT and MMT 3. indicate the flow direction between the two tensiometer.
Some manometers are constructed as in Fig. , whereone side is a large reservoir (diameter D ) and the other sideis a small tube of diameter d , open to the atmosphere. Insuch a case, the height of manometer liquid on the reservoirside does not change appreciably. This has the advantagethat only one height needs to be measured rather than two.The manometer liquid has density ρ m while the air has densityρ a . Ignore the effects of surface tension. When there isno pressure difference across the manometer, the elevationson both sides are the same, as indicated by the dashedline. Height h is measured from the zero pressure level asshown. ( a ) When a high pressure is applied to the left side,the manometer liquid in the large reservoir goes down,while that in the tube at the right goes up to conserve mass.Write an exact expression for p 1gage , taking into account themovement of the surface of the reservoir. Your equationshould give p 1gage as a function of h , ρ m , and the…
Determine the minimum size of glass tube that can be used to... Determine the minimum size of glass tube that can be used to measure water level if the capillary rise in the tube is restricted to 5mm. Consider surface tension of water in contact with air as 0.073 N/m
Fig shows a U-tube differential manometer connecting two pressure pipes at A and B. Pipe A contains a liquid of specific gravity 1.8 under the pressure of 116 kN/m. The pipe B contains oil of specific gravity 0.5 under the pressure of 212 kN/m2. Find the difference of pressure measured by mercury as fluid filling U-tube in mm. The value of x and y are 2.3 m and 1.2 m respectively. PS, Mercury The Mercury level difference (h) in mm
1. A tank is filled with air at a gauge pressure of 6 bar and 55 °C, determine the specific weight of the air in the tank. True changing with time. Non-wo... AURREREAN ly 6. A Venturimeter having inlet diameter 1.8 cm and throat diameter 0.5 cm. The oil-mercury differential manometer has a reading of 5 cm. Calculate the discharge of an oil of SG=0.9.
i need the answer quickly
A manometer showed in Fig. 1 (right) connects pipe A and pipe B. It reaches a balance at the showing state. Determine a) When the pressure in pipe A is increased from the current state by 32 kPa while the pressure in pipe B remains constant, the interface between water and mercury in the left leg of the manometer will go up or down? b) Calculate the change in the elevation of this interface.
A tank containing helium has a manometer attached, as shown in the figure. The local atmospheric pressure, P. is 101 kPa and the gravitational acceleration is 9.81 m/s. The heights of each fluid in the manometer are h,-360 mm, h -450 mm and hs550 mm. Assume the densities of the water (pw), light oil (pw), and mercury (p) in the system are equivalent to those at standard tmospheric conditions. Determine the pressure of the helium in the tank, PHe, in kPa. P. Light Oil. P Helium 5. Water. P.
Don't give wrong answer better skip it