Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wh, Wm, and W; of the head-pipe, muffler, and tailpipe are 12, 98, and 42 N, respectively, and act at the indicated points. If the exhaust-pipe hanger at point A is adjusted so that its tensions F, is 79 N, determine the required forces in the hangers at points B, C, and D so that the force- couple system at point O is zero. Why is a zero force-couple system at o desirable? Fc FB FD 27° 27° c D B Wm r = 0,30 WA +2.4-1.2 0.50 0.50 0.40.3- Dimensions in meters Answers: FB = Fc = N Fo =

Q: An exhaust system for a pickup truck is shown in the figure. The weights Wh, Wm, and W₂ of the…

A: The weight are The force at A is The net moment about O is zero

Q: A wind tunnel model of an airplane wing is suspended as shown in the figure. What is the reaction in…

A: Answer: Tbe reaction in cable C is 3.38 lb. Hence, the correct answer is option (a).

Q: 2. 240 mm 160 mm 240 min 240 mm 240 mm A uniform pipe cover of radius r= 240 mm and mass 30 kg is…

A:

Q: An exhaust system for a pickup truck is shown in the figure. The weights Wh, Wm, and Wt of the…

A: Given data: Weight of head-pipe, Wh = 13 N. Weight of muffler, Wm = 111 N. Weight of tailpipe, Wt =…

Q: P G H P2 a E В a/2 a/2 As shown, a truss is loaded by the forces P = 497 lb and P = 192 lb and has…

A:

Q: A tensile force of magnitude a N is desired to be created on the cable AB.

A:

Q: (a) Revisit the problem and solve for the cable forces TAD, TAC, and reaction force components O Oy,…

A: To find-: a) The cable tensions and reaction forces at O. b) The moment of tension TAc along line…

Q: PROBLEM 1: Consider the truss system to the right. All members are two force members. There is a pin…

A: Consider the truss system to the right. All members are two force members. There is a pin at Point D…

Q: - Neglecting friction forces, and the radius of the pulley. Determine the following: 1- The tension…

A: Given:Force acting on the cantilever veam ,F=140 N

Q: Problem 8: For the 2-member truss ABC: ● Derive a formula for the force in each member as a funtion…

A: For the solution refer below images.

Q: A 1260-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the…

A:

Q: ROBLEM 1: insider the truss system to the right. All embers are two force members. There is pin at…

A: To find out :-Forces in each member.

Q: Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In…

A:

Q: An exhaust system for a pickup truck is shown in the figure. The weights W, W, and W, of the…

A: Write the given data:

Q: Ans: Cx = -267 lbs The neighbor's child wants you to build a sand castle in their backyard. You go…

A:

Q: As shown, a truss is loaded by the forces P = 2.18 kN and P = 0.930 kN and has the dimension a =…

A: At first by the observation we need to identify the zero force member...

Q: 4. A 45-kg street sign is being held in place by three wires and a ball/socket joint. Determine the…

A: The mass of street sign is

Q: QB2: Determine the force in members GH, GB, and BC, and state whether each of these three members is…

A:

Q: Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.