**Chapter 09, Problem 005 GO****Your answer is partially correct. Try again.****Problem Statement:**What are (a) the x coordinate and (b) the y coordinate of the center of mass for the uniform plate shown in the figure if \( L = 17\text{ cm} \)?**Diagram Explanation:**The diagram depicts an L-shaped plate divided into smaller rectangular sections. These sections are labeled with their dimensions in terms of \(L\):- The width and height of the different sections are mentioned as multiples of \(L\).Key measurements are:- The topmost part stretches horizontally \(4L\) and vertically \(L\) from the origin.- The second segment is vertically \(3L\) and horizontally \(2L\) from the initial point.- The third section vertically extends further down to \(4L\) with a bottommost horizontal stretch of \(2L\) and vertical height \(2L\).**Given Calculations:**- For part (a): \( \text{x coordinate} \quad 0.1159 \; m \)- For part (b): \( \text{y coordinate} \quad 0.1159 \; m \).**Answers Entry:**(a) Number: 0.1159 Units: m (b) Number: 0.1159 Units: m These fields are provided to input the calculated x and y coordinates of the center of mass.**Note:** The problem responses here require verification or re-calculation for correctness as indicated.

Answered: Image /qna-images/answer/955456a4-2c7e-474e-aecc-691cebf10d65.jpg

Chapter 09, Problem 005 Go Z Your answer is partially correct. Try again. What are (a) the x coordinate and (b) the y coordinate of the center of mass for the uniform plate shown in the figure if L = 17 cm? 2L 4L 3L 4L 2L 2L 凯

Chapter 09, Problem 005 Go Z Your answer is partially correct. Try again. What are (a) the x coordinate and (b) the y coordinate of the center of mass for the uniform plate shown in the figure if L = 17 cm? 2L 4L 3L 4L 2L 2L 凯

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I:56) Solve it in radians per second please
Calculate the x and y components of a 30m displacement at 23° from the x-axis
okay so basically given the digram below you need to solve for the mass in grams of the 4 unknowns (M1, M2, M3,Mmg). The only known mass is Mnut=16g, and the lengths of the rods used. basically we had to make a mobile and equally balence objects and then determine their masses
Suppose that the coordinate frame 0₁X1Y₁Z₁ is obtained from the coordinate frame ooxoYoZo by a [2²] rotation of 600 about xo axis, what is Ro? Suppose pº R Q Search DII % 5 T FS Y & 7 find p¹. 99+ PrtScn FB S Home End F10 PgUp
Point "P", as shown below, is located between nodes 2 and 3 of a quadratic 1D bar element. Workout the location of point "P" in physical coordinate system (x coordinate) if the location of point "P" in the natural coordinate is p=0.05. Suppose that the locations of node 1 and node 3 are x1 11.2 mm and x3=38.0 mm. respectively. (Hint: the answer should be in mm and you need to round your answer after 4 decimal points) 1 X1 2 x2 * P 3 X3
A crate is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the xy plane. Point A is located at a height of h = 83.82 cm above the top of the crate directly over the geometric center of the top surface. Use the given dimensions from the table below to perform the following calculations: a.) Determine the position vector b.) Compute the unit vector ûCA that points from point point A. c.) If rope AB carries a tension force of magnitude F = 674 → N, determine the force vector FT that expresses how this force acts on point A. 2013 Michael Swanbom cc i❀O BY NC SA Express each vector in Cartesian components to three significant figures. b PAD cm cm that describes rope AD ↑Z cm y Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Be sure to align your cartesian unit vectors with the coordinate axes shown in the figure. Variable Value a
Instruction: Give the step by step solution using autocad
The following model is displayed in the O2-Dimensional O Geotropic Isometric Spatial Render view.
Please see Part B of the attached photo.
Edition Eighth Z▼▲ Ā Mc Graw Hill Vector Mechanics for Engineers: Statics HW: Ch 6 จงหาตำแหน่งของจุดศูนย์ถ่วงของชิ้นส่วนเครื่องจักรกลด้านแกน x ของวัสดุประกอบดังรูป Find the position of the center of gravity of the mechanical part on the x-axis side of the composite as shown in the figure. mm 20 34 mm 62 mm 51 mm 20 mm 200 mm 10 mm © 2007 The McGraw-Hill Companies, Inc. All rights reserved. 45 m 100 mm 55 mm 7-52
4.15. Calculate I,, ly, Iy for the section of Figure P4.9 above. You can use the results from Example B.1.
4G O0: D1 9:24 P Flag question Consider for the part in the figure below, a = 112, b = 50 and c= 100. be 40 a 80 20 Lt----------- Dimensions in mm Analyze the part in order to calculate the coordinates of the centre of gravity in the (x, y, z) system of coordinates. It is assumed that the following process was following for the manufacturing process • Part 1(a cubic piece of dimension 33 x 50 x 60 is cut out of a Part 2 of dimensions 145 x 50 x 80 and then • Part 3 (triangular prism) is welded Part 2 Fill in the table below with coordinates of centers of respective parts in mm Part тт mm mm 1 Part тт mm тт 2 Part тт mm mm 3 The coordinates of the CG are respectively: mm y = mm mm Assume a density of 160 kg/m³ and calculate the total volume and the mass of the part. Volume = mass = kg Check