Centrifugal pump: 010: Choose the correct or best alternative in the following: 1- In the centrifugal rig, a rotameter device is used as, a. a meter for reading temperature difference, b. a meter to have water level height, c. a meter to give water discharge, d. none of these. 2. Screw pump is used for, a. viscous fluids b. non viscous fluids, d. none of these. c. heavy liquids 3. The total head lost in centrifugal pump test is defined as, a. kinetic head lost b. potential head lost c. pressure head lost d. all of these 4- The performance characteristics of the centrifugal pump is compared by, a. the amount of water discharge of the pump, b. type of liquid, (viscous or non-viscous), c. the head of water rise of the pump, d. all of these.

Centrifugal pump: 010: Choose the correct or best alternative in the following: 1- In the centrifugal rig, a rotameter device is used as, a. a meter for reading temperature difference, b. a meter to have water level height, c. a meter to give water discharge, d. none of these. 2. Screw pump is used for, a. viscous fluids b. non viscous fluids, d. none of these. c. heavy liquids 3. The total head lost in centrifugal pump test is defined as, a. kinetic head lost b. potential head lost c. pressure head lost d. all of these 4- The performance characteristics of the centrifugal pump is compared by, a. the amount of water discharge of the pump, b. type of liquid, (viscous or non-viscous), c. the head of water rise of the pump, d. all of these.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The type of steady flow system in which, two streams of fluids m1 and m2 are entering and one stream of fluid m3 is leaving, is known as O a. Turbine O b. Nozzle Oc. Mixing chamber O d. Compressor
is the striking of vapor bubbles during suction at the eye of an impeller of a centrifugal pump due to relatively --pressure. O a. Cavitation, high O b. Cavitation, low O C. Priming, Low O d. Priming, high
gress Check Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal pumps to downstream equipment?
Explain and draw the right procedure of suction piping installation for a negative lift and positive lift of a centrifugal pump
If we assume that a given pump requires 7.50 ft of NPSH when operating at 3500 rpm, what would be the NPSH required at 2850 rpm?
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 1, P1(gage)=______ A. Patm B. 0 C. 101.325 kPa D. It can not be determined.
Compressors work with the gas and air, while centrifugal pump transfers energy. Select one: O True False
Which of the following will increase productivity index of a reservoir? a. Decreasing tubing diameter b. Reducing bottom-hole flowing pressure c. Decreasing the surface pressure d. None of the above
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
When the air bubbles collapse at the eye of the impeller of a centrifugal pump, due to low väpour pressure, it causes O a. Priming b. excess fluid flow O c. Cavitaion O d. excess fluid pressure
why are centrifugal pumps so little used in fluid power systems
2. Common Fluids Conversions - Please calculate the following: a. 50 GPM to ft/s in a 4" Sch 40 pipe b. 15 GPM to lbm/s of Chloroform at 25°C 30 psi to ft lb-/lbm of Water at 50°C 40 ft lbf/lbm to hp of a fluid moving at 150 lbm/min. Reynolds number for 100% Glycerol at 75°C flowing through a 2.5" Sch 80 pipe at 10 lbm/s d. e.