Center of mass Ⓡ C b Pivot VAATATAL A AAZNAVA Load Given the following, what is the maximum angle we can hold the load at before the crane tips over? Load 100 kg i-beam Mass of crane = 2500 kg Length of crane (body) = 4.7 m Length of crane (arm) = 12 m Diameter of tires = 1.1 m

Center of mass Ⓡ C b Pivot VAATATAL A AAZNAVA Load Given the following, what is the maximum angle we can hold the load at before the crane tips over? Load 100 kg i-beam Mass of crane = 2500 kg Length of crane (body) = 4.7 m Length of crane (arm) = 12 m Diameter of tires = 1.1 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.14P: Find the internal force system acting on section 3 for the pin-connected frame.

See similar textbooks

Similar questions

The 60 kg two-wheeled cart is described in the figure and parameter table below, with G indicating the location of the center of gravity. It is to be pulled so that it goes up the small step. Find the normal force on each wheel, and the magnitude and direction of the force applied at handle. HINT: remember that there are two wheels sharing the load @080 BY NO SA 2021 Cathy Zupke 4₁1 G L₁ L₂ parameter value 0.6 0.5 0.8 0.7 0.2 A L3 LA d L3 units m m m m m B L₂ F For the answers, take to the right and up to be the positive directions. The normal force at each wheel at A in the x direction is Ax= 150 XN The magnitude of the force at B is F Measured from the positive horizontal axis, the angle of F= 45 X° = 212 XN
Question 3) The position of the head and neck and the forces acting on the head are shown in the figure. The center of gravity of the head of mass m=8 kg is located at point C. Neck muscle strength of FM=130 N, which makes an angle of γ=65° with the vertical from the B point to the skull, is affected by the neck extensor muscles. The center of the atlantooccipital joint is located at point B. For this flexion position of the head, the FJ joint reaction force, which makes an α angle with the horizontal from point A, acts. (Take the gravitational acceleration g as 9.81 m/s2). Accordingly; a) Calculate the angle α of the FJ joint reaction force with the horizontal. Response b) Calculate the FJ joint reaction force. (Write your result in N.) Answer
Please write solution to be legible and clear. Free body diagram would help me understand better. Thanks
Draw Free Body Diagram
Typewritten for an upvote. No upvote for handwritten. Please skip if you have already done this. Thank you
Free Body Diagram
Dr. Alexander is holding a briefcase with straight arm. Assume weight of the briefcase FB = 35 N, weight of the forearm FFA = 10 N, weight of the upper arm FUA = 15 N, moment arm of FB = 0.45 m, moment arm of FFA = 0.30 m, moment arm of FUA = 0.11 m, and moment arm of Fm = 0.03 m. Also, FM is 35 degrees above the horizontal. Calculate (1) muscle force FM, and (2) joint reaction forces Fj,x and Fj,y
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs
For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
A simple log bridge in a remote area consists of 2 parallel logs with planks across them. The log has an average diameter of 300 mm. A truck moves slowly across the bridge, which spans 2.5 m. Assume that the weight of the truck is equally distributed between the 2 legs. Because the wheel base of the truck is greater than 25 m. Only 1 set of the wheels is on the bridge at a time. Thus, the wheel load on one log is equivalent to a concentrated load acting at any position along the span. In addition, the weight of 1 log and the plank it supports in equivalent to a uniform load of 65 kN/m acting on the log. 1. Determine the max permissible wheel load W based upon the allowable bending stress of of 7MPa. 2. Determine the max permissible wheel load W based upon the allowable shear stress of of 0.75MPa. 3. Determine the max permissible wheel load W based upon the allowable deflection of 6mm. E=7380 MPa
The mass of the board suspended below is 70 kg. What is the tension in the rope, and what is the resulting Normal Force from the Pivot?