CE CLEAR TC Qo Q1 CLK

Q: The initial word of the 4 bit SISO, right shift, shift register shown below is 0110. After 3 clock…

A: Serial In- Serial Out (SISO) It is a type of shift register in which inputs are shift by one bit to…

Q: There are 4 select lines present in a multiplexer. How many input lines aren present  in the…

A: In this case, there are 4 select lines present in the multiplexer.

Q: If an ISR is called as a result of the INTR signal, then it is O an invalid operation a high…

A: According to the question, If an ISR is called as a result of the INTR signal, then it is_____ (a)…

Q: The shift register that would be used to delay serial data by 5 clock periods is Data in a. Data in…

A: (a)

Q: Draw the output signal Q of the D-latch given the inputs Clock and D. The initial value of the clock…

A: Given:

Q: During the execution of an OUT instruction, the /0/M signal will Go low. Tristate. Not be used. Go…

A: Io/M is an active low signal means it can be activated by providing thr low input

Q: Series connection of switches would normally create O NOR logic gate O NAND logic gate O AND LOGIC…

A:

Q: B A OUT AR of-4 0 tiplexer TPL Tristate CLK P Flip-flop output buffer S, =0 So =o clock SP OE LA 320

A:

Q: In the shift register given in the figure, there is a sequence of 1010 bits at the start time. The…

A: Given    1. Given initial stage of the shift register is 1010    2. Here we have made the name for…

Q: In 4bits PISO shift register there :are 3 OR gates and 6 AND gates 3 AND gates and 6 OR gates O 3 OR…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: While CPU is executing a program, when an interrupt occurs then it O follows the next instruction in…

A: Given, While CPU is executing a program, an interrupt occurs then it

Q: 1. Sp Sp Sp Rp Vec Clock input Aulurmatic Reset From the circuit, write the output value Q2 (logic…

A: According to the question, for the given circuit as shown below We need to find the output Q2.

Q: Q In the arithmetic operations in ALU the meaning of arithmetic shift left instruction for a binary…

A:

Q: When does the PLC counter instruction increment its current count? O Whenever the count input…

A: The programmable counter in PLC will act as a counter similar to the mechanical timer.

Q: With the given waveforms for a 4-16 decoder, how do you list a the decimal output values?…

A: Given:Four set of binary bit streams.A0=0000000010, A1=0011001100, A2=0101010101, A3=0001000100To…

Q: Q0 Q1 Q2 Q3 clock - Given: • Counter starts at decimal 9 when Q viewed as a 4-bit unsigned number…

A: Number   Unsigned        Signed (+ve)             Signed (-ve)              0…

Q: Question : with Eight LEDs with 74HC595. This code uses a shift register to use a single data pin to…

A: Given data: 8 LEDs 74HC595 shift register Value of current LED=5 We have to find the value of the…

Q: Design the circuit that displays 35861429 on the seven segment display (just one). Use shift…

A: To design a circuit that displays the number 35861429 on a seven-segment display using shift…

Q: If you have a system with a quantizer of 5V and 3 bits resolution, show the following: 1. The number…

A: Given: A system with a quantizer of 5V and 3 bits resolution. To find: 1. The number of levels. 2.…

Q: Convert numbers as necessary to perform the subtraction (910 - 1710 ) using two’s complement…

A:

Q: What is subtransient and transient fault current? How do they occur in a system?

A: In a system before the fault occurs voltage and current both are symmetrical AC but when a 3 phase…

Q: Q1 D1 Do CLK-

A:

Q: If a DIP switch with 8 switches (0-7) lines up with bit0-7 of the data bus, and switches 1,2,4,5 & 7…

A: In this question,   We need to choose the correct options If switches 1,2,4,5 & 7 are set then…

Q: Which data will be saved in memory? O a. 0100 O b.0110 O .0011 O d. 1001 Elag question

A:

Q: 12.OR AX, 0300H a. Clears bits 8 and 9 b. Set bits 8 and 9 c. Invert bits 8 and 9

A: The given instruction is: OR AX, 0300H

Q: An 8-bit Shift-right register has 00001101 stored. 0111 needs to be loaded into the register. The…

A:

Q: For the three code words:C1= [110110011], C2= [100101100]andC3=[111100101]. Determine the possible…

A:

Q: 5) In an astable multivibrator when the capacitor is capacitor is using a 555 timer, the and the…

A: For the above given question we need to define the behaviour of the capacitor.

Q: Generate a time delay of 20 ms with a 16-bit timer 0. (Crystal frequency 10MHz) When the time is up,…

A: Write a program that does:Generate a time delay of 20 ms with a 16-bit timer 0. (Crystal frequency…

Q: * Q: STATUS Register has individual bits indicate status of ALU operations 6 are status flags and 3…

A: In this question , we will write about status flag and control flag in 8086 microprocessor....

Q: QUESTION 44 The 8259 is a O Low priority interrupt O Tristate buffer Programmable Peripheral…

A: Intel 8259 is a very important device and very commonly with 8085/8086 systems.

Q: The location 1000h holds value 98h and location 35h holds the value 78h. The register A holds 74h…

A:

Q: If BL= 0011 0110, write down the value of the destination register. 6 i. SAL BL,1 ii. SAR BL,3 iii.…

A: SAL BL, 2- Shifts the bits left by 2 positions and insert 0's as left bits.  SAR BL, 2- Shifts the…

Q: 16. What is the two's complement of 1011100111?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask for rest again. The…

Q: During the execution of an OUT instruction, the RD signal will. Go low. Stay high. O Multiplex O…

A: Execution of OUT instruction