Carbon dioxide gas is compressed at steady state from a pressure of 22 lb/in2 and a temperature of 32°F to a pressure of 50 lb,/in² and a temperature of 100°F. The gas enters the compressor with a velocity of 30 ft/s and exits with a velocity of 80 ft/s. The mass flow rate is 3500 lb/hr. The magnitude of the heat transfer rate from the compressor to its surroundings is 5% of the compressor power input. Use the ideal gas model with cp = 0.21 Btu/lb-ºR and neglect potential energy effects. Determine the flow area at the inlet, in ft², and the power required by the compressor to work, in horsepower. Your answer is correct. Determine the flow area at the inlet, in ft². ft² A1 = 0.1765 * Your answer is incorrect. Determine the power required by the compressor to work, in horsepower. Win i 18.868 hp

Carbon dioxide gas is compressed at steady state from a pressure of 22 lb/in2 and a temperature of 32°F to a pressure of 50 lb,/in² and a temperature of 100°F. The gas enters the compressor with a velocity of 30 ft/s and exits with a velocity of 80 ft/s. The mass flow rate is 3500 lb/hr. The magnitude of the heat transfer rate from the compressor to its surroundings is 5% of the compressor power input. Use the ideal gas model with cp = 0.21 Btu/lb-ºR and neglect potential energy effects. Determine the flow area at the inlet, in ft², and the power required by the compressor to work, in horsepower. Your answer is correct. Determine the flow area at the inlet, in ft². ft² A1 = 0.1765 * Your answer is incorrect. Determine the power required by the compressor to work, in horsepower. Win i 18.868 hp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. In a steady flow apparatus 135 KJ of work is done by each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.30 m³/kg, 600 kPa, and 16m/s. The inlet is 32m above the floor and the discharge pipe are at floor level. The discharge conditions are 0.60 m³/kg, 1 bar, and 270 m/s. The total heat loss between the inlet and discharge is 9KJ/kg of fluid. In flowing through this apparatus, does the specific internal energy increase or decrease? And by how much?
Water vapor with a pressure of 160 bar and a temperature of 480°C enters a stable turbine with a volumetric flow of 800 m3/min. About 18% of the incoming mass flow exits a part of the turbine at a pressure of 5 bar, a temperature of 240°C and a velocity of 25 m/s. The rest comes out from another part of the turbine with a pressure of 0.06 bar, a quality of 94% and a speed of 400 m/s. Determine the diameters of each outlet channel in m.
1
1. Combustion gases enter the nozzle of a jet engine at 3.8 bar and 820°C. The nozzle is well insulated and the gases expand down to an exit pressure of 1.1 bar. Determine the temperature and the velocity of the gases at exit from the nozzle assuming the velocity at inlet is negligible. For the combustion gases take c, = 1.15 KJ/Kg. K and the ratio of specific heats = 1.32
A mixing vessel initially contains 3,989.8 lb of liquid fluid. The vessel is fitted with two inlet pipes, one delivering hot fluid at a mass flow rate of 0.454 lb/sec and the other delivering cold fluid at a mass flow rate of 0.288 lb/sec. Fluid exits through a single pipe at a mass flow rate of 1.338 lb/ sec. Calculate the amount of fluid, in lb, in the tank after 16 minutes.
A mixing vessel initially contains 4,485.43 lb of liquid fluid. The vessel is fitted with two inlet pipes, one delivering hot fluid at a mass flow rate of 0.635 lb/sec and the other delivering cold fluid at a mass flow rate of 0.836 lb/sec. Fluid exits through a single pipe at a mass flowrate of 1.144 lb/sec. Calculate the amount of fluid, in lb, in the tank after 44 minutes.
Consider a reactor (combustor) in which fuel (CO) and oxidizer (H₂O) flow steadily. Both streams are separate and at standard conditions. The products CO₂ and H₂, a gaseous mixture, leaves at 500 K and 100 kPa. Both CO and H20 at inlet are in gaseous phase. The mass flow rate of CO is 2.8 kg/sec. The magnitude of heat transfer is (in MJ/sec) O 5.7 O 4.7 O 3.7 O 2.7 O 1.7
A reversible non-flow, constant volume process decreases the internal energy by 315 kJ for 2.5 kg of gas for which R = 430 J/kg-K and k = 1.35. For the process, determine: a) the work; b) the heat; c) the change in total entropy. The initial temperature the gas is 205 °C.
Ten lbm per min of fluid is handled in a reversible steady flow manner by a thermodynamic system located where the local g = 32 ft/s2. For the liquid, p1 = 20 psia, p2 = 80 psia, ρ1= 1.6 lbm/ft3, ρ2 = 0.32 lbm/ft3, v1 = 400 ft/s, v2 = 600 ft/s, u1 = 130 BTU/lbm, u2 = 130 BTU/lbm. During passage through the system, the fluid rejects 50 BTU/s as heat and rises 175 ft in elevation. During passage through the system, the fluid rejects 50 Btu/s as heat and rises 175 ft in elevation. Determine the work in the system, in BTU. Select one: a. – 675.2 b. – 781.8 c. 892.6 d. 987.4