Carbon dioxide enters an adiabatic nozzle steadily at 1 MPa and 500 °C with a massflow rate of 6000 kg/hr and leaves at 1000 kPa and 450 m/s. The inlet area of thenozzle is 40 cm2. Determine the inlet velocity and exit temperature of the CO2.

Carbon dioxide enters an adiabatic nozzle steadily at 1 MPa and 500 °C with a massflow rate of 6000 kg/hr and leaves at 1000 kPa and 450 m/s. The inlet area of thenozzle is 40 cm2. Determine the inlet velocity and exit temperature of the CO2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ Air enters an adiabatic nozzle steadily at 400 kPa, 290°C, and 35 m/s and leaves at 200 kPa and 240 m/s. The inlet area of the nozzle is 100 cm?. Determine (a) the mass flow rate through the nozzle, (b) the exit temperature of the air, and (c) the exit area of the nozzle. R = 0.287 kJ/kg K, Cp = 1.005 kJ/kg K, %3D
A vapor at a flow rate of 3 kg/s enters a group of eight (8)nozzles at 1.5 MPa, 240 oC and a velocity of 480 m/s, and then expands to 0.07MPa. If the efficiency of each nozzle is 0.95 and the cross-sectional area ofeach nozzle is rectangular with sides’ length ratio is 1:2.5. Determine:a- The steam exit velocity for each nozzle and the dimensions of the nozzlesection at its entrance and its exit.b- The steam exit velocity in case of the neglecting the steam entrance velocity
A combustion chamber is made up of 15-cm-diameter tubular combustors. At 550kpa, 480kpa, and 80 m/s, compressed air enters the tubes. A fuel having a heating value of 42000 kj/kg is introduced into the air and burns at a mass ratio of 40 air to fuel. Determine the temperature, pressure, and mach number at the exit of the combination chamber by simulating combustion as a heat transfer process to air.
A tank has 2 ?? of saturated water at 100 ???. It is heated until it is 400°C. What is the change in entropy of the water/vapor inside the tank? You can use: https://irc.wisc.edu/properties/
5.An ideal gas flows into a channel with an average velocity of 10 m/s from an inlet with 苏日 area of 1 m2. The gas is at 1000 kPa and 500°C. Determine the mass flow rate of the gas. The gas constant is 0.287 kPa.m^3/kg.K. ( )
Dry saturated steam at 8 bar expands in a convergent nozzle to a pressure of 0.5 bar and 0.8 dryness fraction. Determine the exit velocity of the steam if the initial velocity of the stream is 125m/s
Steam at 5 MPa and 400°C enters a nozzle steadily with avelocity of 80 m/s, and it leaves at 2 MPa and 300°C. Theinlet area of the nozzle is 50 cm², andthe heat is beinglost at a rate of 120 kJ/s. Determine (a) the mass flow rate of the steam, (b) the exit velocity of the steam, and (c) the exitarea of the nozzle.
Liquid water at 20 Celcius degree is heated in a mixing chamber by obtaining a mixture with asaturated steam as shown in Fig. 2. As shown in this figure, the liquid water, and the saturated vaporenter this chamber with mass flow rate values of 7.2 kg/s and 0.35 kg/s, respectively. On the otherhand, the mixed fluid leaves this chamber at 50 Celcius degree, as a liquid. If the ambient temperature of thesurroundings are at 15 Celcius degree, determine,a) The temperature of the saturated vapor which is entering this mixing chamber,b) The exergy destruction during this mixing process using the entropy balance,c) The exergy destruction during this mixing process using the exergy balance,d) The second law-efficiency of this mixing chamber device, considering this ambient temperaturevalue of 15 Celcius degrees.
Air at 7 kPa, 420 °C, and 400 m/s enters an adiabatic nozzle. The velocity of the air outlet is 700 m/s. Calculate the air outlet temperature.
Qu2. (A) What is fatigue? Mention the sequence of steps involved in fatigue of a smooth specimen. Mention Four (4) factors that affect fatigue of smooth specimens, stating how each affects fatigue life (B) A very wide panel made of a material of plane-strain fracture toughness of Kic=55MPaVm was found to have a central crack of size 2.5mm. It is subjected to cyclic loading at a design (or working) stress of 690MPA and stress ratio of zero. (a) Sketch the stress-time graph of the loading cycle and determine (i) Stress Range, (ii) maximum cycle stress, (iii) stress amplitude and (iv) mean stress (b) Will the initial loading cycle cause the panel to fracture? Why or whynot? Compute the maximum allowable fatigue flaw size that can fracture the panel during the cyclic loading. (Assume that plain strain condition prevails). (c)