Calculate Vp for the circuit below. -22V 39kΩ $3.3k0 C2 C1 1uF B=120 1uF 120Vrms 60HZ $3.9kQ 1ka VD loss = 12mA Vp = 6V 10MO 2.4ka 1.5V

Q: In a transformer having a 10 to 1 ratio, the copper losses in the primary are 15 per cent less than…

A: The transformer problem  can be solved easily.

Q: What type of covers are used with 4 in. Square outlet boxes?

A: The cover types used in 4 in. square outlet boxes are : 1. Single gang raised plaster covers…

Q: Any example traced in your reading material, connections between the current and the potential…

A: Correct option is c.

Q: 12. What is the primary entity that needs to be consulted with in regards to the location of the…

A: According to the electric code, The meter and the service box should be placed outdoor which can be…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Draw the output signal Q of the D-latch given the inputs Clock and D. The initial value of the clock…

A: Given:

Q: 142-0701-801 RF / Coaxial Connector, SMA Coaxial, Straight Jack, Solder, 50 ohm, Beryllium Copper

A:

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: What are the three project categories an electrical contractor may choose to browse?

A: There are different projects in the world, and every project needs some specialty for completing it.…

Q: Determine the size and type of wire to he installed to a building with temperature that reaches…

A: Here ratings of loads are given for a single phase 230 V source. We need to determine the size and…

Q: 6.a. Extreme _______ may cause some nonmetallic conduits to become brittle and therefore more…

A: 6.a. According to article 352 of NEC  Extreme cold may cause some nonmetallic conduits to become…

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: Define cable rating in a built environment

A: Cable selection and application : It is essential to know cable construction, characteristics,…

Q: 12.A. A connector is a _______ device used to connect a fiber to a source, detector, or another…

A: The solution is given below

Q: where is it most convenient to find a PKES system

A: We need to tell about PKES .

Q: What is receptacle load ? Explain under 100 words...

A: The amount of load produced by a device inserted into a receptacle is referred to as a receptacle…

Q: . one of the three terminals of a FET  analogous to the base of BJT IS _______

A:

Q: In a semiconductor it is observed that 80% of the current is carried by holes and 20% by electrons.…

A:

Q: For the circuit shown in the figure below, com

A:

Q: 6- What is meant by one decade, and one octave?

A: We need to define decade and octave

Q: how do you do this problem?

A:

Q: Describe the job of the Board of Electrical Engineering in one sentence.

A: The solution is given

Q: analyse the rating of wires/ cables and mcb used for different types of loads

A: A small circuit breaker called an MCB is used to trip when home appliances experience overcurrent…

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: What is meant by Electric Bid Package?

A: Bid package means the collection of the pertinent portion of the construction documents into a…

Q: Suppose the current in this circuit is I = -35 A. The voltage drop across each circuit element is as…

A: Introduction Voltage drop is a term used in electrical engineering to describe the reduction in…

Q: A protective put can be used for risk management.   A. TRUE B. FALSE

A: ANSWER      TRUE          A protective put can be used for risk…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: In an electrical system, each of the service entrance conductors has an area of 750 kcmil. The size…

A: Given: In an electrical system, each of the service entrance conductors has an area of 750 kcmil.

Q: Determine the minimum number of cubic inches required for two 10 AWG conductors passing through a…

A: AWG or American Wire Gauge is the US standard measure for the diameter of electrical conductors. The…

Q: What is the meaning of calculated load?

A: Since many different loads are connected to an electrical supply, it is extremely important to know…

Q: a metal device box has four 12 AWG conductors, two internal clamps, and a duplex receptacle. Total…

A: A metal device box has four 12 AWG conductors. According to the national electric code table,…

Q: Briefly discuss the loaded and non-loaded telephone cables

A: Loading is the process to increase inductance of line by adding lumped inductors atpredefined…

Q: Each unit of a 100-unit hotel is 12 × 15 ft. In addition, there's a 60 × 20 ft officeWhat's the…

A: To calculate the service demand load for conductor sizing for lighting and receptacles in a 100-unit…

Q: Explain with neat diagram of instrument for the measurement of sunshine hours.

A: instrument for the measurement of sunshine hours

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.