ulate total heat loss per meter length of uninsulated pipe when the water transfer coefficient is 30 W/m². C and the outside heat transfer coefficient is 20 temperature is 15 °C, the outside air temperature is -10 °C, the water side heat W/m². "C T₁ = 15°C A-30 kr/m³R 52mm T -50mpn T₁ - - 10 C h₁ - 20 IF / m³K k=5011/mK

ulate total heat loss per meter length of uninsulated pipe when the water transfer coefficient is 30 W/m². C and the outside heat transfer coefficient is 20 temperature is 15 °C, the outside air temperature is -10 °C, the water side heat W/m². "C T₁ = 15°C A-30 kr/m³R 52mm T -50mpn T₁ - - 10 C h₁ - 20 IF / m³K k=5011/mK

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
a)Identifythe maximum velocitylimitof ammonia gas in the pipe if the flow is to be maintained as laminar flow. b)If the actual velocity of ammonia gas is 0.9 times the maximum velocitylimit, calculatethe heat transfer coefficient and heat transfer flux if the heat transfer area is 0.16m^2. c)Suppose the pipe has an outer diameter of 43.1 mm and the outer surface wall temperature of the pipe is 356 K, determinethe thermal resistance and thermal conductivity of the pipe.
For an exhaust valve, the mass flow rate through the valve is 1.26 kg/s. The flow coefficient is 0.65 and the cylinder pressure and temperature are 625 kPa and 820 K. Assume exhaust system pressure is 103 kPa, the specific heat ratio is 1.4 and R =287J/ kg.K. The effective area of the valve is (SI unit): Select one: O a. 3.45*10-2 O b. 0.85*10-2 O c. 2.2*10-3 O d. 1.85*10-3 O e. 1.42*10-3
Q: Air enters a rectangular duct. Determine the exit temperature of the air and find the rate of heat transfer loss . Taking k = 0.02662 W/m."C. v= 1.702x10 m'/s, Pr 0.7255, C-1007 J/kg. C ,p=1.127 kg/m u= 2.325 kg/m.s Ans : 34.2°C 3776 W Air dact 15 em 2 em L7m Q. Hot air enters a sheef metal duct located in a basement. Determine
48. Water is flowing in a smooth pipe of diameter D. A section of this pipe hav- ing a length of L is heated. Water at the inlet to the heated section has a tempera- ture of Tŋ. Water temperature at the exit of the heated section is Tp. The heated section of the pipe wall is maintained at a constant heat flux so that a constant temperature difference of AT, = T, – T, exists between the wall and the bulk wa- ter temperature. Show that for turbulent flow in the pipe and a specified heated length and pipe diameter, water temperature at the exit of the heated section is given by: 402 0.6 Pr T52 =Tf +0.0876 L AT DO.8 0.2 m
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg.°C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1. Schematic of temperature distribution 2.ΔTLMTD 3.Actual heat transfer rate 4.Cmin 5.Maximum heat transfer rate
P1
Air enters a duct (100 cm *10 cm*10 cm) at 32°C at a rate of 0.28 m/min to cool 138 W electronic component placed on the duct. Assuming 85 percent of the heat generated inside is transferred to air flowing through the duct and the remaining 15 percent is lost through the outer surfaces of the duct. What is the convective heat transfer coefficient (W/m2.°C), Assume fully developed flow for the whole channel length and (if flow is NOT Laminar use Dittus-Boelter equation:Nu=0.023 Re0.8Pr") E1007 J/kg.°C, v =1,654×10 m /s, p = 1.146 kg/m Pr= 0.7268, k = 0.02625 W/m. °C Select one:
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol What is the a.) value of G in kg/s.m2? b.)value of friction factor? 3 significant figures c.)the % of pressure drop? d.)the outlet pressure? e.) compressible or not?
A heat exchanger is to be designed to condense 8 kg/sec of an organic liquid (tsat=80°C, hfg=600 KJ/kg) with cooling water available at 15°C and at a flow rate of 60 kg/sec. The overall heat transfer coefficient is 480 W/m2 -°C calculate: a) The number of tubes required. The tubes are to be of 25 mm outer diameter, 2 mm thickness and 4.85 m length b) The number of tube passes. The velocity of the cooling water is not to exceed 2 m/sec.
3. Vertical turbines are to be used for flocculation in a water treatment plant with a design flow rate of 189,270 m³/day. Flocculation is to be designed with two trains and five compartments per train. The total detention time in this process is to be 25 minutes, and the average temperature of the water flowing into the plant is 10°C. The velocity gradient in the first compartment is to be 70 s¹. Make the following design decisions for the first compartment: a) Determine the dimensions of the compartment. b) Determine the diameter of the impeller. c) Determine the water power required. d) Determine the maximum rotational speed. e) Estimate the pumping capacity of the impeller and circulation time in the tank.
Q:: Flow of hot air through uninsulated square ducts of a heating system in the attic . Determine the exit temperature and the rate of heat loss. Taking k = 0.02953 W/m. C, v= 2.097x10* mis, Pr = 0.7154, kg/m C,=1008 Ans : 75.7 "C , 941.1 W Jkg."C rP = 0.9994 Tom 0mmin