Calculate the velocity of the precession A top consists of a spinning disc of radius 40 mm and mass 0.5 kg mounted at the end of a light rod as shown in figure. The distance from the tip to the centre of gravity is 100 mm. Calculate the velocity of the precession when it spins at 30 rev/min. 30°

Calculate the velocity of the precession A top consists of a spinning disc of radius 40 mm and mass 0.5 kg mounted at the end of a light rod as shown in figure. The distance from the tip to the centre of gravity is 100 mm. Calculate the velocity of the precession when it spins at 30 rev/min. 30°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HW4 A ship has its turbine engine mounted with its axis of rotation lengthways in the ship. When viewed from the back, the engine rotates anticlockwise at 3500 rev/min. The effective rotating mass of the engine is 200 kg with a radius of gyration of 0.4 m. Calculate the magnitude of the gyroscopic couple produced when the ship turns left on a radius of 200 m with a velocity of 3 m/s. Explain clearly the effect of the couple on the motion of the ship.
Question 4 [17] A 3 kg disk shown in Figure 3 is pin supported at its center. The disk is rotated from rest and attains a constant angular velocity of 15 rad/s. If the mass of the rope is negligible and the radius of gyration of the drum is 50 mm, calculate: mass - 3 kg r=100 mm B m mass = 10 kg Figure 3: The 3 kg disk the angular acceleration of the drum, the tension in the rope, and torque experienced by the drum. 4.1. (13) (2) (2) 4.2. 4.3. Examiner Moderator
Figure Q2 shows a 100 kg cylinder device has a radius of gyration, m= 400mm. The cylinder device is rolling down to a liner plane distance of 2 m stating from rest. Assume no friction in all contact surface, determine the angular velocity after the releasing. Which energy method is suitable in this application and why? 600 mm 300 mm 45 Figure Q2
Edit question Calculate the radius of gyration for the system of two tubes and a seat that form a swing with respect to the axis A shown in the figure. The dimensions of this system are shown in the figure below.The tubes have a mass of 19 kg/m. This means that each meter of tube has a mass of 19. Tubes can be thought of as slender rods.The seat has a mass of 23 kg and can be considered as a thin plate. Note that several views of the swing are offered so that you can better understand which is the reference axis A and the necessary dimensions. As you solve the problem, take into account that you are going to fill a table with the following format. It must be filled with the corresponding units.
Consider the wheel shown below with radius R, mass m, and radius of gyration ko¹ The wheel rolls without slipping under the action of a clockwise torque M. At the instant shown the spring with spring constant ks is unstretched. Derive an expression for the velocity of the wheel center of mass G after the center of mass has moved a distance d. (Hint: Use rigid body work-energy principles. The work done to the system by the applied moment is McA0 and A0 can be related to the distace d by the no-slip condition.) Us G R M м, ко ////
A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum. The mass of the drum is md = 100kg and the radius is r = 0.5 m. The radius of gyration of the drum about point O is ko=0.3 m. The mass of the block is mb= 20kg. The block is released from rest. The acceleration due to gravity is g=9.81 m/s2. (1) Calculate the mass moment of inertia of the drum about the point O, IO_______(kgm2) (two decimal places)