Calculate the transfer function in the high frequency limit for a low- pass filter like that shown in Fig. 7 with up to 3 identical low-pass stages containing a resistance and capacitance. v_out_1 v_out_2 v_out 3 R2 R3 100 0 R1 1 kQ 1 kQ V1 ) sine 1 kHz C1 C2 1 uF C3 1 µF 1 uF

Calculate the transfer function in the high frequency limit for a low- pass filter like that shown in Fig. 7 with up to 3 identical low-pass stages containing a resistance and capacitance. v_out_1 v_out_2 v_out 3 R2 R3 100 0 R1 1 kQ 1 kQ V1 ) sine 1 kHz C1 C2 1 uF C3 1 µF 1 uF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Circuits
Q2) For the circuit in Fig. below, obtain the transfer function Vo(w) Vi(w). Identify the type of filter the circuit represents and = 100 S2, L=2 mH determine the corner frequency. Take R1 = 100 = R2 vi(t) R₁ www ell L R₂2 + v (1)
Design an active high pass filter with a specified Passband break frequency of 1.100 rad/sec and a gam equal to 22. use a capacitor Vahe of loont, For these design, Show: ⑥A circuit diagram of final filter design, Label all Components and Indicate the luput and Output Locations. Do not luctude De Power to the op-amp. ⑥The Jw transfer Function For The Filters -D The Passband gan in dB use the tf and bode command In MATLAB a bode Plot for the filter that the Passband to generate Confirming and the break frequency CLabel both 2nd gan Correat A
In the circuit in the figure, Vcc = 18 V and RL = 2.2 ko, while C₁ = C₂ = CE = 0.1 µF. It is also known that for parasitic and wiring capacitors, Cwi = 15 pF, Cwo = 21 pF, Cbc = 27 pF, Cbe = 817 pF and Cce = 25 pF. Accordingly, what is the bandwidth of the system? NOTE-1: The output impedance of the transistor will be neglected in ro calculations. NOTE-2: The high frequency dependence of hfe,, will be neglected. C1 Vcc .470 02 0.91 Q .30 B = 100 C2 CE www RL va
752. See Figure 752. D=5. The Bode gain and phase plots for a RC circuit are shown in the fig. Determine gain (dB), phase (deg), and frequency (rad/sec) for the points labeled A and B. Also find the other exponents (C,E,F). Answers: GdBA,phA,wA,GdBB,phB,wB,C,E,F.
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
For the low-pass active filter shown below, the transfer function is expressed as: V. V ZR + Zc Zc where: 106 = 2000 , Zc jw rad w = angular frequency in [ ZR ZR Vi o V. 4-A) Show that the e can be written as: V. 500 V 500 + jw 4-B) What should be the value of w so that the magnitude of V10 ? 4-C) With w = 1250 rad/s, and Vị = 9el1.8 – j10 volts, evaluate the magnitude and phase of V. Vo (Hint: evaluate in polar form, and Vị in polar form, then V, = x Vị ) 4 4-D) When 4 modules of this filter are cascaded, the total transfer function will be (. Use de Moivre's Theorem to find the expression of the total transfer function in polar form. Then, find determine the value of w so that the magnitude of the total transfer function is V10 ?
Analogue Electronics II Design 2 different configurations of active band pass filter for the frequency with bandwidthof 200 Hz.Design A has the quality factor Q less than 10, is independent on the critical frequency,whereas Design B has the quality factor, Q more than 30, is dependent on the criticalfrequency. You can use your own value of resistors and capacitors in the design. Show allrelated calculations (eg. fc, fo, Q, Gain, Bandwidth) and the final circuit design.
Parameter Value Gain, AV 30 dB Resistor, R1 1.5 kΩ Capacitor, C 3.35 uF 1. Figure depicts a first order low pass filter and Table tabulates parameters ultised to construct the filter. In the design, R1||R2. Calculate the bandwith of the filter. 2. Describe the condition of unity gain in an amplifier and determine voltage output, VO,if voltage input, V1, is 2V for a non-inverting amplifier 3. Construct an equation relating the input (Vin) and output (Vout) of an inverting amplifier.The conditioning circuit has input range between 10 mV to 110 mV which resultingoutput between 0V to 5V.
I need the answer as soon as possible
H.W2: a) Using 0.1 µF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jwo)where wo is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at w,?
answer with explanation ..