The following arrangement model represents the behavior of the asphalt sample under constantstress. Calculate the total strain when the stress was removed after 3 sec.TG1-1.1 G2G279.7 G2In :9.3 61

Answered: Image /qna-images/answer/238432c5-8538-4409-8d63-9f2bbab78b8c.jpg

Answered: Calculate the total strain when the…

Engineering

Civil Engineering

Calculate the total strain when the stress was removed after 3 sec.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter20: Design Of Rigid Pavements

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

Circly was used to analyse a pavement structure. The horizontal tensile strain at the bottom of a subbase made of lean mix (lean rolled ) concrete was 106 microstrain. Assume RF = 1 Estimate the allowable number of standard load repetition.
Figure (1) shows a pavement structure composed of three layers with their details. If the HMA and the base layers are combined into one layer with the same total thickness (HMA+base layers), what should be the equivalent elastic of the combined layer modulus so the tensile strain at the bottom of the HMA= 0.0006 in. 30000 Ib 150 psi HMA laver E, = 400,000 psi V,=0.4 6 in E, - 20,000 psi Granular base V,=0.4 20 in layer Subgrade layer E, = 10,000 psi V;=0.4 Attach your answers with used charts or tables
Q.21. In the PCA design procedure of rigid highway pavements, as the stress ratio (applied flexural stress divided by 28-day modulus of rupture) decreases, the allowable load repetitions increases.a. Trueb. FalseQ_22. In the PCA design procedure of rigid highway pavements, the fatigue damage is calculated at the pavement edge.a. Trueb. FalseQ_23. In the PCA design procedure of rigid highway pavements, the erosion damage analysis was devised to control the following distresses:a. Subgrade erosion, pumping and faultingb. Shattered slab and ASRc. Shrinkage cracking and joint sealant deteriorationd. None of the above Q_27. The PCA design methodology for airfield rigid pavements is based on the interior bending stress at the bottom of the slab.a. Trueb. False
1. Figure (1) shows a pavement structure composed of three layers with their details. If the HMA and the base layers are combined into one layer with the same total thickness (HMA+base layers), what should be the equivalent elastic of the combined layer modulus so the tensile strain at the bottom of the the HMA= 0.0006 in. 30000 Ib 150 psi E, = ? 6 in HMA layer Ej = 400,000 psi V;=0.4 Granular base E = 20,000 psi V=0.4 20 in layer Subgrade layer E3 = 10,000 psi Vz=0.4 %3D
22. In the PCA design procedure of rigid highway pavements, the fatigue damage is calculated at the pavement edge.a. Trueb. False
A 150mm diameter cylindrical concrete specimen was tested for splitting tensile strength. The Sample failed when the applied force was 120 kN. What is the splitting tensile stress at failure in MPa? The sample length is 300mm
In specific gravity test for coarse aggregate we found the following results: dry weight A= 3008 grams SSD weight B = 3037 grams %3D Submerged weight C=1907 grams The SSD specific gravity Select one: O a. 2.456 O b. 2.877 O c. 2.688 O d. 2.899
A soil element beneath a pave ment experiences principal stress rotations when the wheel load, W, passes over it and moves away, as shown in Figure 10.51. In this case, the wheel load has passed over points A and B and is now over point C. The general state of stress at these points is similar to the one shown by a stress block at point D. The phenomenon of principal stress rotation influences the permanent deformation behavior of the pavement layers. Investigate how the magnitude and the orientations of the principal stresses vary with distance from the point of application of the wheel load. Consider the case shown in Figure 10.51. An unpaved aggregate road with a thickness of 610 mm and unit weight of 19.4 kN/m3 is placed over a soil subgrade. A typical single-axle wheel load, W = 40 kN, is applied uniformly over a circular contact area with a radius of R = 150 mm (tire pressure of 565 kN/m2). The horizontal and shear stresses at each point are calculated from a linear elastic finite element analysis for a two-layer pavement and are presented in the following table. a. Use Eq. (10.28) to calculate the vertical stress increases at soil elements A, B, and C that are located at radial distances 0.457,0.267, and 0 m, respectively, from the center of the load. Determine the total vertical stress (y) due to wheel load, the overburden pressure at each point, and enter these values in the table. b. Use the pole method to determine the maximum and minimum principal stresses (1 and 3) for elements A, B, and C. Also determine the orientation (s) of the principal stress with respect to the vertical. Enter these values in the table. c. Plot the variations of 1 and s, with normalized radial distance, r/R, from the center of loading.
A core sample of granite, 12 cm long and 6 cm in diameter, was tested in unconfined compression. The granite was known to have a modulus of elasticity of 16 x 10^3 MPa. a. At a pressure of 69 MPa, what would be the reduction in length of the sample b. At this pressure what would be the vertical load on the sample? c. At 69 MPa stress the core showed an increase in diameter of 0.011 mm. What is the Poisson's Ratio for the sample?
Pls do all parts and correct I'll rate your solution
Example 2.1: A tire with 689 kPa air pressure distributes a load over an area with a circular contact radius, a, of 127mm. The pavement was constructed with a material that has a modules of elasticity of 345000 kPa and a Poisson ratio of 0.45. Calculate the radial-horizontal stress and deflection at a point the pavement surface under the centre of the ire load. Also, calculate the radial- horizontal stress and deflection at a point at a depth of 508mm and radial distance of 254mm from the centre of the tire load. (USE: Ahlvin and Ulery equations).
The concept of ‘barreling’ was discussed as it related to the standard testing of concrete cylinders. In addition to be observed in concrete this is observed in other materials. What is meant by ba rreling (i.e., the bulging of the center portion of the cylinder during the test) and how would it influence the results of a compressive test?