Calculate the total deflection in the given beam with the following conditions. The concrete beam is 250 x 350m mm dimension with a span of 10 meters is pres- stressed by 2 cables with each cable carrying an effective force of 250 KN. The first cable is parabolic with an eccentricity of 50 mm below the centroidal axis at the center of the span and 50 mm above the centroidal axis at the supports. The second cable is parabolic also with an eccentricity of 50 mm at the center of the span only. The beam supports a uniformly distributed live load of 5 KN/m and Ec = 38 KN/m?.

Calculate the total deflection in the given beam with the following conditions. The concrete beam is 250 x 350m mm dimension with a span of 10 meters is pres- stressed by 2 cables with each cable carrying an effective force of 250 KN. The first cable is parabolic with an eccentricity of 50 mm below the centroidal axis at the center of the span and 50 mm above the centroidal axis at the supports. The second cable is parabolic also with an eccentricity of 50 mm at the center of the span only. The beam supports a uniformly distributed live load of 5 KN/m and Ec = 38 KN/m?.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the safe span (in m) that a 100 x 150 mm purlin would have if it has a spacing 800 mm on centers, to carry a roof load of 60 Pa and a wind load of 1.4 kPa acting on the vertical surface. Allowable bending stress is 10 MPa and the allowable horizontal shearing stress is 0.4 MPa. The allowable normal deflection is 1/360 of span. Weight of purlin is 5 kN/m3. The pitch of the truss is 1/4. and E = 17.3 GPa.
Please provide clear solution.
a triangular beam having a base 400mm and a height of 500mm. if fc'=25MPA and the subjected maximum moment is 15 kN- m. considering uncracked analysis. what is the actual tensile stress?
A rectangular beam 350 mm wide is to be designed for an ultimate moment of 750 kNm with f'c = 28 MPa and fy = 415 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. %D 1. Determine the depth of the stress block if the tensile strain is 0.005 when the concrete crushes at a strain of 0.003. (in mm) (one decimal place) 2. Determine the total amount of tension reinforcement for the given condition above. (in sq.mm) (whole number) 3. Determine the amount of compression reinforcement required. (in sq. mm) (whole number)
Find the collapse load for the truss shown in the figure. All three bars have the same plastic axial strength 125 kN. 5.40m 9.60m D C 7.20m А
5-67. The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel supporting cables when the slab is held in the horizontal plane as shown. X 0.5 m 2m 15 kN Te B Imm TA 2 m
3
Situation 1: A 40-mm diameter post is being supported by two cables on each side. With a tumbuckle attached to each cable, it is tightened until each cable reaches a stress of 50 MPa. turnbuckle A What is the stress experienced by the post? (MPa) 60 60
"D.35. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 25.8 MPa, fy= 506.8 MPa, bf= 710 mm, t= 90 mm, hw= 470 mm, bw = 440 mm ds= 10 mm, ct- 30 mm, cb = 35 mm. Steel bar details: compression side at top (single layer): 4- 16 mm dia. , tension side (double- layered): upper layer is 4 - 28 mm dia. and lower layer is 5 - 28 mm dia." Use the editor to format your answer br ... Ct Bar diameters and positioning in the figure given are just representations. Refer to the problem statement for the ds hw number of bars and bar diameters to use in your computation. 25 mm Cb bw
The built-up cross-section of the 2.0-m, fixed-base column shown below comprises three 300-mm × 25-mm plates that are welded together. The column is subjected to a 300-kN compressive axial load and moments of 100 kN.m and 50 kN.m about the x and y axes, respectively, at its free end (top). Using Fusion 360, compute maximum tensile and compressive stresses (along z) at mid-height of the column (sufficiently far away from stress concentration zones) and compare them with your hand calculations.\ Answers will be: Cross-section area = 22500 mm2 (5 points) Ix = 453,125,000 mm4 (5 points) Sx = 2,589,286 mm3 (5 points) Iy = 112,890,625 mm4 (5 points) Sy = 752604.2 mm3 (5 points) Stress caused by the axial load = -13.33 MPa (5 points) Stress caused by Mx = ±38.62 MPa (5 points) Max Stress = 91.72 MPa (5 points) Min Stress = -118.39 MPa (5 points)
The beam in the figures below has the cross section and loading indicated therein;determine for the most requested section, knowing that the allowable normal voltage is 1400kgf/cm².a) Determine Momentum andDevelop the structure efforts diagram and indicate the Most Requesting Section.b) Determine the area and Center of Gravity (G) of the structure.and Determine the Moment of Inertia Jz. c) Determine the maximum tensile and compression stresses, express the distribution of stresses in the figure and check the beam would you be able to do the calculations identifying a, b and c please
Uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel supporting cables when the slab is held in the horizontal plane as shown.