Calculate the time constant measured from the cursors below? 0.ov Ssiys 5asus 9 Transient_Analysis.raw Cursor 1 V(out) Horz: 499.58735µs Vert: 5V Cursor 2 V(out) Horz: 508.52499µs Vert: 2.5000778V Diff (Cursor2 - Cursor1) Horz: 8.9376478µs Vert: -2.4999222V Freq: 111.88626KHZ Slope: -279707

Q: To which input would you connect a reference voltage to make an inverting level detector?

A: Reference voltage is a voltage in an electronic component or circuit that produces a constant DC…

Q: why thermal noise is treated as AWGN?

A: Additive white Gaussian noise (AWGN): In the Information theory it is used to emulate noise effect…

Q: In a spread system, there are many different kinds of tools that could be used.

A: Step-1->A spread system is a type of communication system that spreads a signal over a wider…

Q: In |type of control system, controller gets the sampled error signal.

A: This is the question based on control syatem subject . In this the error sampled signal is present…

Q: What is a hazard of push buttons

A: What is a hazard of push buttons ?

Q: 3. If CR1 coil is latched on, what will happen to the contacts drawn below? CR 1B F 昇 CR 1A 4. When…

A:

Q: Suppose you have measured a time delay of 70 microseconds between the two cursors below. The signals…

A: In this question We need to determine the angle between both signals in degree.  We know Frequency…

Q: metal outer casing backing block electrodes power cable piezoelectric crystal acoustic plastic…

A: Ultrasound probes are that act as the primary tools for the Ultrasound machines If the probes, are…

Q: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

A: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

Q: [Positive Th output voltage of the given electronic controller is /Negative ]voltage. Ri Vin Vout

A:

Q: Differential Current pressure True flow rate Differential Orifice Chart ADC plate pressure…

A: Orifice Plate: It has a disc with a hole at its centre, through which the fluid flows. The pressure…

Q: 37. What can be adjusted to provide any value of voltage between 12 and 0 volts? a. rheostat - b.…

A: In this question, choose the correct option What can be adjust to provide any value of voltage…

Q: Which one of the following is not an example of non contact type displacement sensor? O eddy current…

A: which one of the following is not an example of non contact type displacement sensor ? a. Eddy…

Q: Explain the difference between accuracy and precision in an instrument?

A: Error can be defined as the difference between measured value and true value.

Q: 4. Describe with the help of a diagram how differential pressure transmitter can be used to measure…

A: Hey, since there are multiple questions posted, we will answer first question. If you want any…

Q: sensors employed to determine the position of an object in relation to some reference point.

A: The displacement sensor is the sensor that finds the distance between a certain point and the sensor…

Q: Draw and label the block diagram of the instrumentation calibration chain.

A: Instrument calibration- Calibrating an instrument is to ensure that the instrument is working…

Q: Briefly explain different types of moving iron instruments with appropriate

A: Moving iron instrument : A tool in which a moving metal is used to measure the flow of current or…

Q: An FM broadcast-band receiver tunes to 88-108 MHz. Calculate the range of local oscillator…

A:

Q: 12. Which speed sensor can also be used as an alternating current (AC) generator? Group of answer…

A: In  this question,  Choose the correct option Which speed sensor can also be used as an alternating…

Q: ra 5- Find the pulse width for a monostable timer if R= 100KSN and C= 100μF?

A: In this question we need to find a pulse width of monostable timer.

Q: please write details about Sensor Soil moisture

A: Soil moisture sensor in the electrical apparatus is used to measure the moisture content of the…

Q: Three closed-loop poles of a system are in the Left-Half plane and one in the Right-Half plane means…

A: The given statement is TRUE because any no of poles on the Right Hand Side of s-plane make a system…

Q: Compare series, shunt, and chopper type JFET switch.

A: When VGS is high then JFET operates in ohmic region and when VGS is low then JFET operates in cutoff…

Q: 1- What does the air volume sensor mean? What are the electrical lines of this sensor, explain?

A: Note: As per the guidelines will be solving only 1st question. For others please repost. Generally,…

Q: Explain the following sensors with neat diagram. (construction, operation and applications )   a)…

A: According to the question, we need to explain the following sensors with neat diagram.…

Q: Fill in the blank: SC is a connector is also known as stick and click.

A: Fill the blank, SC is... Connector is also known as stick and click.

Q: With reference to the diagram, explain how the ultrasound probe can be used to both generate and…

A: Solution: Determine : here explain given diagram for each part.

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Which is not part of a cathode-ray tube oscilloscope? a. Electron gun b. Digital panel meter C.…

A: Given that parts of cathode ray tube oscilloscope

Q: a/an ___________________ measurement, the ultrasonic level sensor's analog output gets larger as the…

A: The explanation is as follows.

Q: Why two-tone test signals are used for making PEP measurements?

A: 2-tone testing is a method of detecting intermodulation distortion in electrical components and…

Q: Explain the working of Capacitive Level sensor with a neat diagram.

A: A capacitive fluid level sensor is an instrument for estimating the stature of a fluid and changing…

Q: a) Which type of control system is used in the given block diagram? Write the definition. Output…

A:

Q: a) Which type of control system is used in the given block diagram? Write the definition. Output…

A: The given control system doesn't have any feedback path connected from output to input. Hence ,this…

Q: Please answer in typing format

A: Step 1:In order to sketch the root locus of the given transfer function we will use the open loop…

Q: Whcih one of the following sensor can be used to measure linear displacement? a. Load cell b. LVDT…

A: The functions of the given sensors are given below in brief:

Hall Effect Sensors

The hall effect sensor is an electronic device designed to detect the effect of the hall, and converts its findings into electronic data, or opening and closing the circuit, providing a magnetic field measurement, processed by an embedded computer or displayed on a visual connector.