Calculate the tension T in the cable which supports the 1000-lb load with the pulley arrangement shown. Each pulley is free to rotate about its bearing, and the weights of all parts are small compared with the load. Find the magnitude of the total force on the bearing of pulley C .T 0=30° C B A 1000 lb

Calculate the tension T in the cable which supports the 1000-lb load with the pulley arrangement shown. Each pulley is free to rotate about its bearing, and the weights of all parts are small compared with the load. Find the magnitude of the total force on the bearing of pulley C .T 0=30° C B A 1000 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
A 200 lb block is in contact with a plane inclined at 30ᵒ with the horizontal. A force P parallel to and acting up the plane is applied to the body. If μs = 0.20, Determine: a. The force P required to just impend motion up the plane. b. The force P just to prevent motion down the plane.
6.62 Neglect the mass of the pulleys and the link. The block has a weight of 230 lb and the cord is attached to the pin at B. The pulleys have radii of r1 = 2 in. and r2 = 1 in. Determine the force P on the cord. Determine the angle θ that the pulley-supporting link AB makes with the vertical.
5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body weight acts through the tibia. The Achilles Tendon makes an angle (0) of 8° with the vertical and for this foot x1 is 6.2 cm and x2 is 12.3 cm. Calf Muscle Tibia Achilles Tendon Calculate the tension (T) in the Achilles Tendon if a 70 kg man stands on the toes of both feet. Using the values in this example what is the mechanical advantage for this lever and describe what that means in terms of the efficiency of the lever.
Find the crushing force exerted on the rod at B and the magnitude of the horizontal and vertical reactions at pin A, given:F = 55 lbs, L1 = 8.5 in, L2 = 2.3 in, θ = 26 °
Very urgent The elements of the spring loaded mechanism for the car tailgate are shown in the figure. For the shown equilibrium state, two curved springs are used on the AB connection. The mass of the tailgate is 18 kg with the center of mass G. Calculate the loads carried by the O connection. The influence of the weights of the other components is negligible.
Draw the free body diagram
Determine the reaction forces at the support A and the tension force T in the cable needed to support the 225 kg mass as shown in the figure below. Neglect the weight of the arm AB. 2.5 m |350 225 kg
2m 1m 1m -2m- 2m 2m The crate weighs 450 kg andis supported by three cables as shown in the figure 3 m below. D a. Draw a free-body diagram for point A b. Express the tension in each cable in terms of the unit vector andits unknown magnitude c. Determine the magnitude of the tension in each cable d. Whatis the maximum weight for a cratel that can be supported if the maximum tension in any çable is 900 kg?
A smart phone is sitting in a docking station. The docking station has a mass of 510 g and the phone, 85 g. Determine the reaction forces at the two supports. 65 mm 70 mm 60° 150 mm (Express your answers using two significant figures.) FA = N FR = N
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 777TT ring 24 Cable 7 A r= 0.5 m 30 0.5 m B. 2 m 1 m 1 m 30
Determine the forces in cables AB and AC required to hold the ball of mass M= 126 kg as shown in figure below to be in equilibrium. Take tension in the cable AD= 200 N. Also, draw the free body diagram of joint B and joint D.