Calculate the super elevation ё for a railroad track having a rail guage of 1560 mm for a 600 meter radius curve at a rated speed of 80 kph. What is the flange pressure F exerted on the wheels of 46,000 kg car coach traveling the curve at a maximum velocity of 120 kph

Calculate the super elevation ё for a railroad track having a rail guage of 1560 mm for a 600 meter radius curve at a rated speed of 80 kph. What is the flange pressure F exerted on the wheels of 46,000 kg car coach traveling the curve at a maximum velocity of 120 kph

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 12.20 The flat-bed trailer carries two 1500-kg beams with the upper beam secured by a cable. The coefficients of static friction between the two beams and between the lower beam and the bed of the trailer are 0.25 and 0.30, respectively. Knowing that the load does not shift, determine (a) the maximum acceleration of the trailer and the corresponding tension in the cable, (b) the maximum deceleration of the trailer.
The barge is 10 m wide by 30 m long. When loaded with 5 MegaNewton-force, its center of gravity is 0.5 meters above the water surface. 13. Find the value of MBO? 14. Find the metacenter height above the center of gravity for a roll angle of 10 degrees. 15. Compute the righting moment.
A crate of 400 lb is resting on a rough horizontal surface having a coefficient of friction of 0.40.Determine the force P required to cause a motion to impend if applied to the crate on thefollowing listed below.a. Horizontallyb. Downward at 30° with the horizontal
11.7 (A/B). A solid shaft carrying a flywheel of mass 100 kg and radius of gyration 0.4m rotates at a uniform speed of 75 rev/min. During service, a bearing 3 m from the flywheel suddenly seizes producing a fixation of the shaft at this point. Neglecting the inertia of the shaft itself determine the necessary shaft diameter if the instantaneous shear stress produced in the shaft does not exceed 180 MN/m². For the shaft material G= 80 GN/m². Assume all kinetic energy of the shaft is taken up as strain energy without any losses. [22.7 mm.]
Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-mcounterclockwise couple (a) Free Body Diagram (b) Determine the load intensity, w at B and the distance “a” (c) what are thereactions at A and B ?
A 10 kg block slides down a smooth inclined surface as shown below. Determine the terminal velocity of the block if the 0.1-mm gap between the block and the surface contains SAE 30 oil at 60°F. Assume the velocity distribution in the gap is linear, and the area of the block in contact with the oil is 0.1m². 0.1 mm gap 120°
needs to be solved by either distribution of forces or parallelogram law.
Given two infinitely wide parallel horizontal plates that are moving at different velocities at a space of H between the plates. The top plate is moving faster than the bottom plate. The flow is fully developed and laminar with no driving pressure gradient. Determine: A) an equation for the velocity as a function of depth B) an equation for the average velocity C) the flow rate per unit width U2 Us with the outside rotation faster than the inner rotation. Also, it may simplify your calcs by defining U2 – Uj as AU Note: while this seems like a non-physical problem, it mimics the pattern of a double rotating bearing
Please solve correctly
Determine the resultant of the line loads acting on the beam.
Q5: The space between a square smooth flat plate (50 x 50) cm², and a smooth inclined plane (1:100) is filled with an oil film (S.G. 0.9) of 0.01 cm thickness. Determine the kinematic viscosity in stokes if the plate is 2.3 kg. The velocity of the plate=9 cm/sec. = CA Wsine VW 100 1
I need the answer as soon as possible