Calculate the stress developed in the following members that are each subjected to an axial tensile load of 80 kN: steel bar, 25 mm by 50 mm 150-mm-diameter wood post (use the given diameter) Assume the modulus of elasticity for steel to be 30,000,000 psi (207,000 MPa) and the proportional limit to be 34,000 psi (234 MPa).

Calculate the stress developed in the following members that are each subjected to an axial tensile load of 80 kN: steel bar, 25 mm by 50 mm 150-mm-diameter wood post (use the given diameter) Assume the modulus of elasticity for steel to be 30,000,000 psi (207,000 MPa) and the proportional limit to be 34,000 psi (234 MPa).

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter48: Applications Of Formulas To Spur Gears

Section: Chapter Questions

Problem 68A

See similar textbooks

Similar questions

Compute the number of cubic centimeters of material in the locating saddle shown. Round the answer to the nearest cubic centimeter.
Suppose that r=12 cm and h=15 cm in the right circular cylinder. Find the exact and approximate a lateral area. b total area. c volume.
A steel rod 3/4 in. in diameter and 25 ft long is subjected to an axial tensile load of 15,000 lb. Compute a. stress b. strain c. total elongation
Suppose a 1.6-oz golf ball is placed on a vertical spring with force constant k = 2 lb/in. The spring is compressed 6 in. and released. About how high does the ball go (measured from the spring’s rest position)?
Calculate the maximum bending stress produced in a 1/32 -in. -diameter steel wire when it passes around a 24-in.-diameter pulley.?
A sawn lumber column with a 5.5 × 5.5-in. cross section has an 11-ft effective length. Knowing for the grade of wood used the adjusted allowable stress for compression parallel to the grain is oc= 1000 psi and the adjusted modulus E= 540 x 103 psi, determine the maximum allowable centric load for the column. The maximum allowable centric load for the column is TEkips.
A 60-mm-diameter solid aluminum post is subjected to a horizontal force of V = 25 KN, a vertical force of P = 70 kN, and a concentrated torque of T = 3.25 kN-m, acting in the directions as shown in the Figure. If L = 90 mm. Determine the normal and shear stresses at (a) point Hand (b) point K. T "| P HK X L
A swimming pool is 6 feet deep atthe deep end. It is 10 by 16 feetat the top and 10 by 4 feet at the bottom ∆V=5ft3 Assuming that water has a density of 62.4 pounds per cubic foot, find theweight/force of ∆V and include units.
A trough whose cross-section is a trapezoid, measures 6 meters across the bottom and 8 meters across the top, and is 3 meters deep. If the trough is filled with a liquid of mass density p, what is the force due to hydrostatic pressure on one end of the trough? Write your answer in terms of p.
A solid, round simply supported steel shaft has a diameter of 38 mm and a span length of 800 mm. The shaft supports a concentrated load of 3 kN at midspan. Calculate the maximum deflection of the shaft. Use the formula method. For steel members, use a modulus of elasticity of 30,000,000 psi The given loads are superimposed loads; neglect the beam weight; neglect shear and moment considerations. Use any appropriate method to calculate deflection.
2. A steel rod 10 ft long is made up of two 5ft lengths, one ¾” diameter and the other½” in diameter. How much will the bar elongate when subjected to an axial tensile loadof 5000 lb
A hollow circular steel shaft has a 100-mm outside diameter and a 75-mm inside diameter. Calculate the allowable torque that can be transmitted if the allowable shear stress is 65 MPa. When the allowable torque is applied, calculate the shear stress at the inner surface of the shaft.