Answered: Calculate the reliability of the…

Calculate the reliability of the following system if all the components have a reliability of 0.8. 2 3 4 2/3 system 4 1 4 6 4 2/5 system 7 8. 6

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter16: Installation Of Heating, Cooling, And Refrigeration Systems

Section: Chapter Questions

Problem 18RQ

See similar textbooks

Related questions

Q: 2.Fringing effect is a phenomena occurs in ........... (a) Transformers. (b) Electrical field. (c)…

A: We are authorized to answer only one question at a time since you have not mentioned which question…

Q: A generator feeds power to an infinite bus through a double circuit transmission line. A3 phase…

A: Given: A generator feeds power to an infinite bus through a double circuit Transmission line. 3…

Q: Identify the low voltage system from the following. a. primary distribution b. Secondary…

A: A low-voltage network, sometimes known as a secondary network, is a component of electric power…

Q: ings of a 40 kVA, 6 m respectively. The le- ate (i) the primary vol ced (ii) the full-load re

Q: Alnalysis 4. a. Find the no-load value of vo b. Find vo if RL = 15 KN %3D c. How much power is…

A: To solve above problem, we will use Ohm's law and Kirchhoff's law: Ohm's law state that in a current…

Q: Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor m Non- linear, Load…

A: The given circuit is shown below.

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

6.
Calculate the reliability of the following system if all the components have a
reliability of 0.8.
3
4
2/3 system
6.
2/5 system
4
7

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The maximum electrical trade size of intermediate conduit is a.) 150 mm b.) 125 mm c.) 200 mm d.) 100 mm
(a) Describe how TLBs are used to increase paging efficiency.
:A-choose the correct answer for the following: I-Using a solid in the neutral and the earth in the systems that Operating voltage is: (a)below 2.2kV & above 33kV (b) between(2.2kV to 33&V) 2-In ungrounded system such repeated charging and discharging of line to ground capacitance resulting in repeated arcs is called: (a)fault current (bjarcing ground (cjearthing current 3-Using earthing transformer in the: (a)Star-connection system (b) Delta connection system (c)Star & delta connection system
Find the minimum size EMT raceway required to carry three (3) 500kcmil, three (3) 3/0AWG and two (2) #6 AWGconductors
17. Which of the following measurements should be recorded in installation documentation?A. Multimeter measurementsB. OTDR measurements onlyC. Power meter measurements onlyD. All power meter and OTDR measurements
Equal area criteria is a method used to calculate: Select one: O a. None of the answers b. Critical clearing angle and time for transient faults O c. Critical clearing voltage angle for transient faults d. Transient stability current limit O e. Steady state stability power limits
There are 144 fuel cells are joined in a series through interconnects.there will be 4 stacks having 36 cell in each stack.these stacks are then oragnised in series and parallel combination to form a single module to deliver required voltage and output power.this SOFCs module then combined with CHP system to get thermal . From this data answer the following questions. a)Calculate voltage losses of module?.this question is very compulsory. b)Electrical efficiency of module? C)Thermal efficiency when module combine with CHP system? D)Combined electrical and thermal efficiency? The input parameters of single cell are given below: Ocv=1.020 Current density=2250mA/cm2 Power density=850mw/cm2 Cell active area= 121cm2 Net power=15kw System fuel utilization=80% Operating temp=550°c Cell voltage=0.8v Power of single cell=103 watt.
what is vehicle servicing
Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment problems. Electronics equipment become more susceptible to voltage sag, hence the companies experience production stoppages. Voltage sag analysis is very complex issue. Based on voltage sag randon factors describe on it.
In your own words and from your own understanding, avoid plagiarism or copying from the Course Material, explain or describe MOLDED CASE CIRCUIT BREAKER.
Note : You have to click SUBMIT before the end of the time. So when the invigilator announce that you F click SUBMIT, then you must click it, otherwise your answers will not be saved. Hi, Mohammed Salim Ahmed Al. When you submit this form, the owner will see your name and email address. Assume that 8oW bulb and 100w bulb are connected in parallel and supplied by 240V ac .When 80w bulb is damaged then .. O Circuit breaker will trip and supply will be cutoff O 100 w bulb also will get damaged after some time O 100w bulb will glow very dim O 100w bulb will continue to glow with same brightness 32°C Sunny A O D 40) G E Chp prt sc delete home 8 backspace { O L 1. pause
The parameters of the _________equivalent circuit are defined in general terms for any operating conditions. a.hybrid-pi b.hybrid c.re d.pi