Calculate the moment of inertia of the shaded area about the x-axis. 86 mm 86 mm 61 Answer: lx = i (106) mm4

Q: elow, it consists of two supports AB and BC. If none of the angles ions to calculate the possible…

A:

Q: DONT MIND THE BIG NUMBER ON THE RIGHT, IT IS JUST FOR NUMBERING. MAKE SURE IT IS CORRECT AND…

A: Solution:-Given thatW=314 Nμs=0.214

Q: For the beam and loading shown, determine the location (m) from point A of the resultant of the…

A: Solution:-Given thatW=27065 N/mV=75424 N/mx=1.47 my=4.54 mz=1.81 m Concept:-Area of distributed load…

Q: * find the tension in the cable that holds up the beam and the magasto and direction of the force of…

A: Here, the angle between the wire and the beam is determined by basic trigonometry that is, The…

Q: At time t = 0 a small ball is projected from point A with a velocity of 174 ft/sec at the angle 64°.…

A: The answer for this question has solved below...

Q: I Review | Constants In the figure below (Figure 1), suppose the object is a square steel plate,…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: To find the forces in members BC,BE, and EF. To solve for each from an equilibrium equation which…

Q: 2. The force P = 2 kips is applied to point A, and is supported by cable AB, cable AC, and bar OA.…

A:

Q: A fireworks show is choreographed to have two shells cross paths at a height of 107 feet and explode…

A:

Q: The force P is applied to the 31-kg block when it is at rest. Determine the magnitude and direction…

A: mass of the block, m=31 Kg Angle of inclination, θ=15°The magnitude and direction of frictional…

Q: The beam supports the triangular distributed load shown below with wmax = 510 lb/ft. The reactions…

A: Please refer to solution in Handwritten form for better understanding.

Q: 2. A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of…

A: Diameter of rivet d=3/4 inch=1.9*10-2m, Plate thickness t=25mm, Shearing stress of rivet s=80…

Q: 3. Now suppose the length and diameter of the cork were measured. Archimedes' principle was used to…

A: Archimedes’ principle is very beneficial for calculating the volume of an object that does not have…

Q: ) For the system shown in (FIG.) determine the resultant and locate it w.r.t. point A? 120KN

A: Draw the given diagram with resultant force and resultant moment.

Q: Zero error is +0.005 cm, What is the correct diameter?

A: Given data,  Least count =0.01 mmIt is used to measure the diameter of a wire.Reading of the sleeve…

Q: 1) Return to your data table above and continue to collect data for those points for when the scale…

A: Solution Given below:

Q: away at the rate of 48 fusec a. What is the rate of change of the height of the top of the ladder?…

A: Given:- L= 25 ft Vx = d(x(t))/dt = 48 ft/sec   at x= 7 ft

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A: Given : value of a =21 in we need to find the location of centroid of the area by direct…

Q: Guy wire AB is used to help support the utility pole AC. The guy wire AB can support a maximum and…

A:

Q: Consider an infinitely long l-beam. There is a Gaussian distribution w(x) acting over the entire…

A: Given: Let us consider the given wx=e-xm-12 kNm

Q: A particle is launched from point A with a horizontal speed u and subsequently passes through a…

A:

Q: The measurements x1 = 10m, x2 = 8m, and x3 = 6m represent the sides of a rectangular parallelepiped…

A:

Q: In any problem, if the number of unknowns is greater than the number of equilibrium equations, the…

A: The 1st question is unclear. Please repost with necessary information. We are solving the 2nd…

Q: Determine the x- and y-coordinates of the trapezoidal shape. 2.3 b Answers: (x, y) = (i b 1.8 b x Mi…

A: Divide the figure into two parts:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: We need to apply pythagorous theorem for figure to calculate length of ACXAC2 = AB2+BC2AC2=(11.5')2…

Q: 7. A horizontal beam 6.0 m long projects from the wall of a building. A guy wire that makes an angle…

A: Given, L=6.0mθ=400

Q: Company Z is having problems with the press shown in figure No.3. The company has informed us that…

A: Given: Let us consider the given data, μ=μc=0.125P=5500 lbd=3 inpitch=14=0.25 indc=2.5 in Let's…

Q: A solid uniform ball with mass m and diameter d is supported against a vertical frictionless wall by…

A: Draw the free-body diagram of the uniform solid ball.

Q: 27. A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 50.0-gram…

A:

Q: The density (mass/volume

A: Given data: The density of the aluminum is ρ. The expression for the density is given by: ρ=mV…

Q: Find the theoritical value of "F" and compare that with an experimental value provided to you…

A: It is a simple force balance lever problem.

Q: The force F is applied 45 degrees counter clockwise from the surface of the slope. The slope is 20…

A: Given data:  Force (F) = 60 lbs Angle with surface of slope (θ) = 45° Required: The magnitude of the…

Q: Determine the magnitude of the pin force at A. Assume W = 525 lb, a = 3.7 ft, b = 2.7 ft, r = 8 in.…

A:

Q: bar is 4 m and its weight is 250 The wire can withstand a maxin

A: Given as, Length of bar, L=4 m Weight of bar, Wbar=250 N Weight of block, Wblock=350 N Maximum…

Q: Find the shear and moment equations for the beam loaded as shown if P = 467 lb, W = 245 lb/ft, a =…

A: