Answered: Calculate the Modulus of Elasticity of… | bartleby

Related questions

Question

Calculate the Modulus of Elasticity of Material 1 from the curve above.

570 MPa
Material 1
500 MPa
480 MPa
Material 2
350 MPa
Densities
P1 = 2.75 kg/dm3
P2 = 2.30 kg/dm3
0.009 0.012

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Consider a metal bar of length L, cross-sectional area A, and Young's modulus Y. When a tension force F is applied to the bar, it causes an extension AL. Model the material as a cubic lattice, where the atoms lie at the corners of the cubes and are connected by springs with equilibrium length x. Calculate the force constant k of the atomic springs by deriving expressions for (1) the number of atoms in any cross-sectional area, (2) the number of atoms in a single chain of length L, (3) the microscopic extension Ax between atoms, (4) the tensile force f between atoms, (5) write f = kAr and show that k = Yr, (6) calculate the value of k for a typical metal such as aluminum, for which Y = 70 GN/m² and x = 0.4 nm.
For a brass alloy, the stress at which plastic deformation begins is 350 MPa, and the modulus of elasticity is 103 GPa. (1) What is the maximum load that may be applied to the specimen with a cross-sectional area of 135mm without plastic defomation? (2) If the original specimen length is 78 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
Calculate the work done in stretching steel wire of length 2 m and of cross sectional area 0.0225 mm², when a load of 100 N is applied slowly to its free end. (Young's modulus of steel = 20 x 1010 N/m²)
the point that identifies the proportional limit of the material whosee graph of stress as a function of strain is shown as?
Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm, and length 248 mm subjected to a tensile load of 50 kN which produces an extension of 0.25 mm. O a. 124 GPa O b. 125 GPa O c. 122 GPa O d. 152 GPa
Step 1 First option says : The relative amount of deformation of a material, this is called strain not stress. second option :the relative force resisting deformation of a material due to an external load on the material , this is the young modulus. fourth option :the amount a material can stretch before it breaks ,it is called elastic limit. Last option : The amount of energy that can be absorbed by a material before it breaks ,it is called the energy . third option :the force applied to a material . and also stress is defined as force applied to a material per unit cross sectional area. Step 2 Hence the correct option is : the force applied to a material .
Consider a titanium cylindrical wire of 3.0 mm in diameter and 2.5x102 mm in length. Calculate your elongation when applying a 500 N load. Assume that the deformation is fully elastic. Data: Ti elastic coefficient: 107 GPa.
A rubber band 20 cm long has a cross-sectional area of 4 mm . What load will stretchthe rubber band 1 mm if the modulus of elasticity of rubber band is 4 x 10-15dynes/cm2?
Problem Solving... A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 10^6 psi. Find Poisson's ratio for the specimen. O 0.33 O 0.40 O 0.95 O 0.30 Вack Next Clear form
Consider a titanium cylindrical wire of 3.0 mm in diameter and 2.5x102 mm in length. Calculate your elongation when applying a 500 N load. Assume that the deformation is fully elastic. Data: Ti elastic coefficient: 107 GPa.
A cast iron rod of diameter 22 mm and length of 250 mm is subjected to a tensile load of 90 kN, and produces an extension of 0.45 mm. Calculate the modulus of elasticity 4
As soon as possible

SEE MORE QUESTIONS