Calculate the minimum radius (in mm) of the solid aluminium tent pole required to carry the weight of the tent without buckling. Assume the tent pole is restrained sufficiently at the top and base, such that the pole effective length can be assumed to be equal to its actual length (H). Where W = 141.4 kg , H = 2.7 m, and take gravity to be 10m/s² , Young's modulus of aluminium, Eal = 69,000 MPa

Calculate the minimum radius (in mm) of the solid aluminium tent pole required to carry the weight of the tent without buckling. Assume the tent pole is restrained sufficiently at the top and base, such that the pole effective length can be assumed to be equal to its actual length (H). Where W = 141.4 kg , H = 2.7 m, and take gravity to be 10m/s² , Young's modulus of aluminium, Eal = 69,000 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
Question 1 of 5 A column with a length of 5 m is fixed on both ends. The column is made of an Aluminum I- beam 7 x 4 1/2 x 5.80 with a Moment of Inertia ly = 5.78 in (2.406 x 10-6 m*) and a cross-sectional area of 4.93 in? (3.181 x 10-3 m²). The Modulus of Elasticity for aluminum is 69 GPa and the factor for a column fixed in both ends is 4. a. Find the Euler Load for this Column b. If the FS is 2, what is the maximum allowable load for this column? Answer using this format: A. GIVEN B. FORMULA C. SOLUTION with unit analysis D. FINAL ANSWER
SITUATION I: A 50-m steel tape is of standard length under a pull of 5kg and a temperature of 22 degree celcius when supported throughout its entire length. The tape weighs 0.06 kg/m, has a cross section area of 0.06 cm'and a modulus of elasticity of 2x10°kg/cm?. The tape was used in the field to measure a distance that was determined to be 525.48. At the time the measurement was made, the constant pull applied was 10kg with the tape supported only at endpoints. During measurement, the temperature was observed to be at an average of 19 degree Celsius. Use alpha a= 12.36x10/degree celcius. 1. Determine the correction due to tension. a. 0.021898 m b. 0.021895 m c. 0.021911 m d. 0.021589 m 2. Determine the correction due to temperature. a. 0.01984 m b. 0.01968 m c. 0.01986 m d. 0.01948 m 3. Determine the correction due to sag. а. 1.8998 m b. 1.8898 m c. 1.8888 m d. 1.9898 m 4. Find the corrected length of the line a. 523.5826 m b. 524.5823 m c. 525.6832 m d. 526.3628 m
65 A block is of width 60 mm and weight W. A force P is applied to block at height h. Coefficient of friction between block and floor is 0.3. Upto what height h force can be applied so that the block slips without tipping? (a) 120 mm (c) 105 mm 60 mm- (b) 110 mm (d) 95 mm h μ = 0.3
В 70 mm M 70 mm 70 mm 70 mm 70 mm 70 mm A beam is bent about its centroidal horizontal axis by moment M as shown. The allowable stresses for the material used in the beam are 120 MPa in tension and 180 MPa in compression. Determine the maximum moment that can safely be applied to the beam. Express your answer in kNm and using three significant digits.
Determine the value of Eld for the beam loaded as shown. 60 lb/ft malo...... A B 1200 lb-ft 10 ft
65 A block is of width 60 mm and weight W. A force P is applied to block at height h. Coefficient of friction between block and floor is 0.3. Upto what height h force can be applied so that the block slips without tipping? (a) 120 mm (c) 105 mm 60 mm- (b) 110 mm (d) 95 mm h μ = 0.3
Consider the metallic structure composed of two homogeneous beams connected by a C joint, with the dimensions and load indicated in the figure. Disregard the friction and the proper weight of the beams. Determine the values of internal efforts in the section located in E.
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.38 in. when the tension in the rod is 2300 lb. If the diameter of the rod is 0.376 in., determine the maximum length of the rod. O 199.3 in. O 236.3 in. O 183.5 in. O 248.3 in. O 219.2 in.
A simply supported I-beam is loaded with a distributed load, as shown. The deflection, y, of the center line of the beam as a function of the .position, x, is given by the equation: where L-4 m is the length, E=5 GPa is the elastic modulus, I=60 x 10^(-6) m^4 is the moment of inertia, and wo=20 kN/m. Find the position x where the deflection of the beam is maximum in meters. Express your answer in meters with six decimal digits after decimal point. Wox y = 360LEIL*- 10L2x² + 3x+)