Calculate the minimum copper conductor size needed for 120/240 V electric range branch circuit the electric range has a nameplate rating of 12 KW?

Q: There are three 15,000-ohm resistors connected in series across a 120-volt DC source.  What is the…

A: The solution can be achieved as follows.

Q: 46. The standard ampere rating for fuses includes per NEC 240.6(A) а. 1 а b. 6 A C. 601 A d. All of…

A: Fuse is an electrical safety device that operates to provide overcurrent protection of an electrical…

Q: Whether Surge resistor 10 Ohms should include in calculation?

A: Surge resistor: It is a resistor which is inserted between the rectifier circuit and filter circuit…

Q: Using spray arc transfer, amperes are used with a 0.045" (1.1mm) electrode to weld stainless steel.…

A: Spray arc are generally the droplets which are around the arc to the weld pool used to increase the…

Q: ectrician A says that a circuit breaker marked 120/240 V is acceptable for a circuit that doesn't…

A: Answer: B.  Electrician A is correct

Q: This Multiple choice questions from electronics lab course & just write for me final answer , It…

A: power is the multiplication of the voltage and current Given Pz = 1.5 W Vz = 5.3 V

Q: When installing grounding electrode conductor at services, it's common to use a single large common…

A: Here we discuss about grounding/earthing related concept.

Q: What is the negative effect of operation a contactor coil above or below it's rated voltage

A: The contactor operational limit is 85 to 110 percent of the rated coil voltage.   The percent…

Q: Hi, for electric circuits with both current and voltage sources present what is the fastest way to…

A: Hello,The fastest way to do the analysis with both current and voltage sources present,  depends on…

Q: If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load?

A:

Q: in which part o NEC article 690 provides requirements for installation of disconnect in a…

A: NEC stands for National Electrical Code and NEC Article 690, Solar Photovoltaic Systems, provides…

Q: Identify and describe the operations of all major equipment used in substations

A:

Q: What is different cost of electrical energy?

A: In real world nothing comes for free, everything has their own cost to produce or use it. Similarly,…

Q: What is factor of a cable at 5 degrees celcius when calculating resistance

A: The solution is provided in the following section.

Q: A 14/2 type NM copper used for a general lighting branch circuit Ampacity : Maximum fuse or circuit…

A: Circuit breaker:- Circuit breakers are used for safety purpose in electrical equipment. It is used…

Q: L 1. A single SPST switch is rated for 20 A/28V. Can this switch be used to control a 12-V, 540-W…

A: Given Data:An SPST switch with,Current rating Voltage rating Load voltage Load power To…

Q: What is the minimum sized PVC Schedule 40 conduit we should use for the above wire run if it is…

A: 3/4".     To determine the minimum size of PVC Schedule 40 conduit required for a wire run, we need…

Q: Subject - Explain the different methods of electricity distribution. Question - Describe the…

A: Electricity is generated in power plants. The majority of power plants are positioned far from load…

Q: What are the primary functions of a power substation in an electrical grid?

A:

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.