Calculate the mass of flue gases flowing through the chimney when the draught produced is equal to 1.9 cm of water. Temperature of flue gases is 290°C and ambient temperature is 20°C. The flue gases formed per kg of fuel burnt are 23 kg. Neglect the losses and take the diameter of the chimney as 1.8m.

Calculate the mass of flue gases flowing through the chimney when the draught produced is equal to 1.9 cm of water. Temperature of flue gases is 290°C and ambient temperature is 20°C. The flue gases formed per kg of fuel burnt are 23 kg. Neglect the losses and take the diameter of the chimney as 1.8m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3) The temperature of the vehicle cabin is 72F and Ø = 50%. pR (i) the partial pressure of the air and water vapor (ii) the vapor density, and (iii) the 29.92 in. Hg Find humidity ratio of the mixture. Ans. (i) 14.496 psi , 0.1941 psi, (ii) 0.000613 Ib/ft3, (iii) 0.00833
Wastewater containing lead is being released from a certain industrial plant. The stream contains X.YZ % Pb and is treated in a unit (maximum capacity = 5000 kg wastewater/hr) that removes 90% of lead in the feed, which is then recycled back into the plant. Another stream from the unit is being released to a lagoon. If the stream leaving the plant has a rate greater than that of the treatment unit. the excess of the capacity of the unit (say, the excess above 5000 kg/hr) bypasses the unit. This excess is combined with the liquid leaving the treatment unit, which is released into the lagoon. The treatment plant releases 7500 kg/hr of wastewater. Let X.YZ be 7.23 Calculate the mass fraction of Pb in the waste lagoon stream. Express your answer in 4 decimal places.
This question is about Hohmann transfer orbits. One possible method to terraform the planet Mars is to increase it's water content. This could be achieved by changing the orbits of icy asteroids in the asteroid belt so that they hit Mars and deliver their water to the planet. (a) Assuming an initially circular orbit for an asteroid with an orbital radius of 2.52A.U. and a circular orbit for Mars of 1.52A.U., calculate the du required for the asteroid to be moved onto a transfer orbit that will bring it to the orbit of Mars. You may find it useful to follow the following steps. (i) Determine the initial orbital velocity of the asteroid. (ii) Determine the eccentricity of the transfer orbit between the two circular or- bits. (iii) Determine the velocity of the transfer orbit at perigee. (iv) Determine the velocity of the transfer orbit at apogee. (v) Determine the change in velocity required to move from a circular orbit to be at apogee for the asteroid.
c) The data obtained from air monitoring station in one area are as follows: (CO2,C4) Carbon monoxide 18.50ppm Ozone 0.53ppm Nitrogen oxide 5.80ppm Nitrogen dioxide 3.00ppm Sulphur monoxide 0.70ppm
Please don't give image based answer..thanku Question:- Water vapor enters a continuous flow adiabatic turbine at 9 MPa pressure, 450 o C temperature and 188 m/s velocity, and exits at 50 m/s speed at 20 kPa pressure and 92% dryness. Calculate the turbine inlet cross-sectional area since the mass flow rate of the steam is 12kg/s.
The aluminum fuel tank (α = 23.8 x 10-6 m/moC) on a sailboat measures 40 cm by 50 cm by 75 cm. If it is filled with 10oC gasoline from an underground tank, how much fuel will leak out when the fuel and the tank return to 28oC ambient temperature?
Explain the nozzle efficiency and its significance.
Compute the total wark done by a gas system following compression processes as shown below. Express your answer in KJ. 02 04 06 Vim'
What is normal air flow rate? How is air flow pressure measured?
i need the answer quickly
For an exhaust valve of 1.43 * 10-3 m? effective area, calculate the mass flow rate through the valve (SI unit). The flow coefficient is 0.65 and the cylinder pressure and temperature are 625 kPa and 820 K. Assume exhaust system pressure is 103 kPa, the specific heat ratio is 1.4 and R =287 J/ kg.K.
Saturated steam at 10 bar pressure is supplied to increase the temperature of the feed natural gas from its inlet temperature of 30°C to within 15°C of the steam outlet temperature. All steam properties can be verified in the steam table, attached. Evaluate the mass flow rate of the steam supplied, if about 20% of the steam is still uncondensed at the exit. The relevant properties of Natural gas (NG) are as follows: NG Flow Rate = 1500 kMol/hour Average specific heat Capacity of NG = 40 kl/kMol.°C.