Calculate the joint rotation at support C (0c) for the continuous beam ACE shown in figure by moment distribution method. Draw BMD and SFD for the beam.The beam is subjected to loads X kN (downwards) and 15 kN (Upwards). EI is constant throughout the beam. 17.2KN 15 kN B D 2.0 m 2.0 m 2.0 m 2.0 m 4.0 m 4.0 m El constant

Q: Find the area and put in square feet

A:

Q: What is DALR line?

A: Lapse rate: The rate at which an atmospheric variable that shows the variation of moist adiabatic…

Q: Convert 10 in to centimeter' 1 Add file

A: answer = 25.4 cm  explanation is given in below step

Q: ( Centroid: Centroid is an imaginary point in a section where entire area of section is assumed to…

A: Brief concept introduction- The centroid is the average position of an object's points. When the…

Q: given triangle ABC find side c

A:

Q: D. SKETCH: (Draw the resulting figure based on the data given on a graphing paper. Vertical axis or…

A: Station BS HI FS IFS Elevation (m) BM -1 1.515 101.515     100 0+000       1.520 99.995…

Q: Determine the X coordinates of the centroid of the trapezoidal area shown.

A: Given data : The given figure in divided into Rectangle and Triangle Rectangle: Width (B)=120 mm…

Q: 1/2x10ft

A: We are given: 1/2×10 ft   The given expression is equivalent to computing half the length of 10 f.

Q: Define earth work

A: The engineering work that is created by moving and/or processing unformed rock or large amounts of…

Q: How stadia interval factor is determined?

A: The Stadia interval: The Stadia interval is defined as the ratio between the focal distance between…

Q: り Iy= ? 「ん

A:

Q: 0+365 0+370 0+375 0+380 BM2 1.008 0.953 0.880 0.800 0.783 COMPUTATIONS: 1. Computing Height of…

A: The formulas to be used are given in question

Q: Write the units used by English systems to specify small areas?

A: Solution: In the English system, areas are basically given in square feet or square yards. For…

Q: 1. GIVEN: REQOIREO: yo l0". 7,9 to locete the centreid t 6"

A: To find centroid

Q: Define Transform faults.

A: Transform fault is a kind of fault in which two tectonic plates slip past each other.

Q: A S 84 16'51" E B. D N 80°31'12" W ZA = %3D ZB = ZC = ZD = Next » S 3 27'40" E N 20°36'19" w

A: given question is from surveying we have to find interior angles of traverse

Q: Give the coordinates for the following autocad drawing

A: The points are named as below

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: These are angles whose sum is 360°. complement djacent pplement plement

A: These  are angles whose sum is 360 A) complement B) adjacent C) supplement D) explement

Q: -20 -0.5a 2a/3 T=0.5a

A:

Q: how far is the center of the circle x^2+y^2-6x-8y-11=0 from the y axis asap pls

A: Express the equation in the general form. Then compare to find its center

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: locate the centroid area of the plate, all the unit is in mm.

A: Labelled diagram of the different section -

Q: 610 mm 813 mm y 1220 mm 660 mm

A: Given Data  volume is given cuboid and right angle triangular prism with x=1220 mm y=813 mm z=660 mm…

Q: X coordinate: X = X 2A₁ X₁ +A₂X₂+2A3X3 24₁ +4₂ +243 2x(2.83x0.4)x+(2.44x0.4)x+2x(0.72x0.4)x2.63…

A:

Q: Which Coordinate System can be defined with its origin at any location and with its three axes in…

A: Cartesian coordinates allow one to specify the location of apoint in the plane , or in thethree-…

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: How many divisions are on the vernier scale?

A: A vernier scale is a visual representation that uses mechanical approximations to obtain an exact…

Q: II I I| |||| Using the contour map what are the elevations of the contour lines Labeling Contours…

A:

Q: the elevation of the contour line that has the highest elevation?

A: From the contour line having elevation 495m towards the counter line having elevation 500m, we can…

Q: B Look to the Contour map above Solid line is the ground surface level Dashed line is Water table…

A: Contour lines are drawn on contour maps which represents the elevation or depression at any…

Q: Determine centroidal coordinates of the volume. 610 mm 813 mm 1220 mm wu 099

A: Consider the figure,

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: Draw the orthographic Projections of given object.

A:

Q: State the Characteristics of the contour lines from H to A

A: General characteristics of counter lines : 1. Must close on themselves, on or off the map. 2.…

Q: 1 / 2 \text { inch } \times 1 / 4

A: To find:- 1/2*1/4

Q: What is the WGS84 datum?

A: WGS84 Datum

Q: B 75 mm 250 mm 40° A

A: Draw FBD: let us suppose AB as part 1 and BC as part 2: l1=250…