1. Calculate the factored tensile resistance of a L127 x 89 x 9.5, CSA G40.21 350W,connected with 6 - M16 bolts. End distance is 35mm and bolt spacing is 50mm. Usethe usual gauge distances found on Page 6-181. Assume punched holes and shearededge condition.6- M16 bolts50 50 35usual gauge distances

L127x89x9.5 CSA G40.21 350W 6 bolts of M16 End distance =35 mm Spacing = 50 mm Ag=1980 mm2 Dia of…

Answered: Calculate the factored tensile…

Engineering

Civil Engineering

Calculate the factored tensile resistance

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: m

A: Applied tensile load = 330000 N = 330Kn Maximum Allowable Stress = 110 Mpa…

Q: Tensile strength became. . when * .cohesive of particles absent ten five zero

Q: 2. The tensile link shown is flat, is 5 mm. thick, and carries an axial loac a. Compute the maximum…

A: GIVEN- Axial load (P)=1350 N Thicknesss (t)= 5 mm

Q: 4. The horizontal bar shown is supported by a pin at A and two rods with identical length. Determine…

Q: Given: A steel rod (A= 150 mm²) is stretched between two fixed points with a tensile load of 5000 N…

Q: 3. The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the…

Q: 6. Value of Young's modulus of elasticity of steel if , Bulk modulus is 160 GPa and Poisson's ratio…

Q: What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the…

Q: A typlcal aluminum-alloy scuba diving tank Is shown. The outside diameter of the tank is 200 mm and…

A: Maximum shear stress in plane = pd/8t Where, d = inner diameter d = 200-2*12 = 176mm

Q: Shown is a copper bar which has a diameter of 10 mm and loaded by tensile load P = 0.0137 MN The…

Q: Cg Methed f Sectins loo kw determine forces in FE, FC bC ノ

A: Hello dear this is the solution of your problem The answer is found to be Force in members…

Q: The plates in the figure below are each 3 inches by 0.5 inches in cross section. If the hole in each…

A: Solution:- Given information: Cross section of plate =3×0.5 in Hole diameter, d=1316 in, and Load,…

Q: diameter of washer = 9/8 inch = stress in the nut 18 ksi g stress 800 psi

A: d=7/8 inch dia of root thread = 0.731 inch din = 9/8 inch tensile stress = 18ksi bearing stress =…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied…

A: Given Data Modulus of elasticity Steel (Es) = 200 GPa = 200 × 103 N/mm2 Bronze (EB) = 83 GPa = 83…

Q: A 10 inch long silver wire is stretched to a total length of 11.50 inches. Find the value of strain

Q: Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area…

Q: 0.5 mm 350 mm - Bronze A = 1500 mm² E = 105 GPa x = 21.6 x 10-6C 450 mm Aluminum A = 1800 mm² E = 73…

Q: (15 POINTS) The steel bar has the dimensions shown. Determine the maximum axial force P that can be…

Q: Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together…

Q: What would be the temperature at which the bar will have a compressive stress of 3 MPa given that at…

A: Elongation due to temperature change δT=Lα(ΔT)ΔT=T2-T1=T2-(-20)=T2+20

Q: An aluminium wire (E=10,600 ksi) having a diameter d%-1/8 inch. and length L=14 ft is subjected to a…

Q: 2- The Tensile stress of AISI 1035 Cold-dra (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.

A: AISI stands for American Iron and Steel Institute- AISI 1035 is a water resistance carbon steel.…

Q: 8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa.…

A: GIVEN Modular ratio, m = 11 Modulus of elasticity of steel, Es = 200,000 MPa To Determine Value of…

Q: Calculate the tensile steel strain of 5-16-mm-dia rebars in a concrete beam 200 mm by 440 mm at…

Q: An axial bar fixed at both ends with no loads applied is subjected to ar increase of temperature.…

Q: THEORY OF BENDING TEST OF REINFORCING STEELBAR

A: Bending Test of Reinforcing Steel Bar- The bending test is used to determine the ductility of steel…

Q: e beam is made from a material that can safely support a tensile or c Based on this criterion,…

A: Reactions :∑ MB=0RA1.6-F1=0RA=FA1.6Max moment :MMax=RA1=FA1.6 kN-m

Q: When designing a structural member, which of the following statements is FALSE? Select one: A. The…

A: B. The ultimate stress depends on the Factor of Safety used. This statement is FALSE. Ultimate…

Q: 12 ID 12 Draw the Mohr's circle. Find the stresses on the plane shown. Fill in the blanks and table.…

Q: mechanical properties changes during tensile test

A: Mechanical properties- These are those properties which changes due to change in temperature,…

Q: Gusset plate Column Pin diameter = Steel plate Pin 80 mm 16 mm 10 mm thickness one 40 kN For the pin…

A: Determine 1. Normal stress acting on the gross area. 2. Normal stress acting on the net area. 3.…

Q: As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial…

A: Step 1 To Determine - Stress in bronze

Q: DISCUSS THE STRESS-STRAIN RELATIONSHIP SHOWN BELOW (WRITE IN ENGINEERING LETTERING) Actual Rupture…

Q: Two plates are bonded together by glue as shown. If P = 60 kN and the allowable shear stress of the…

Q: Show Stress/ strain curve for nitinol and steel (2 separate charts please)

Question

1. Calculate the factored tensile resistance of a L127 x 89 x 9.5, CSA G40.21 350W,
connected with 6 - M16 bolts. End distance is 35mm and bolt spacing is 50mm. Use
the usual gauge distances found on Page 6-181. Assume punched holes and sheared
edge condition.
6- M16 bolts
50 50 35
usual gauge distances

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Sketch the stress-strain curve and explain it in relation to the tensile test for steel bars.
What do you call the stress caused by the application of couple in the material?
Please show a detailed solution and explanation including its FBD. Thank you!
Round off final ans only, dont round initial values
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
SIR, SOLVE THE QUESTION PROPER AND CORRECTLY. THANKS.
Topic: Stresses in Beams (Given formulae: Fb =Mc / I for bending stress v = VcA' y' / Ib for Shear stress)
Read the question carefully and give me all right solutions with clear calculations.
Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
Sketch a sample stress-strain behavior of steel and identify different levels of strength.
What is another term for bend? (A) flex B compress fracture D) twist E stretch
I need the answer as soon as possible