**Title: Calculating Circuit Current**Calculate the current from Vs and the current going to Ground (bottom of the diagram) for the following circuit. Use the following parameters for the circuit: - Vs = 10 V- R1 = 470 ohms- Vf for D1 and D2 = 2.1 V- R2 = 110 ohmsShow your calculations.**Diagram Explanation:**- The circuit diagram consists of a voltage source (Vs) at the top.- There are two resistors: R1 and R2. R1 is positioned before any diodes, and R2 is after. - Two diodes, D1 and D2, are connected in series between the resistors.- The circuit concludes with a ground connection at the bottom.**Instructions for Calculation:**To calculate the current through the circuit, consider these steps:1. **Determine Total Voltage Drop Needed for Diodes:** - Each diode has a forward voltage (Vf) of 2.1 V. - Total Vf for both diodes = 2 * 2.1 V = 4.2 V.2. **Calculate Voltage Drop Across Resistors:** - Vs provides 10 V. - Voltage left for R1 and R2 = Vs - Total Vf = 10 V - 4.2 V = 5.8 V.3. **Calculate Total Resistance:** - Add R1 and R2: Total resistance (Rt) = R1 + R2 = 470 ohms + 110 ohms = 580 ohms.4. **Use Ohm’s Law to Calculate Current (I):** - I = Voltage across resistors / Total resistance = 5.8 V / 580 ohms.Through this process, students can find the current from Vs and the current flowing to the ground.

We will find out current for given circuit . Both diode will be forward baised .

Calculate the current from Vs and the current going to Ground (bottom of the diagram) for the following circuit. Use the follow parameters for the circuit: Vs = 10 v, R1 = 470 ohm, Vf for D1 and D2 = 2.1 V, R2 = 110 ohms. Show your calculations. Ri Rz

Calculate the current from Vs and the current going to Ground (bottom of the diagram) for the following circuit. Use the follow parameters for the circuit: Vs = 10 v, R1 = 470 ohm, Vf for D1 and D2 = 2.1 V, R2 = 110 ohms. Show your calculations. Ri Rz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the equivalent resistance of the circuit (Ohms) when R1 = 29 Ohms and R2 = 68 Ohms?
R1 is connected in series with R2 and R3. R2 and R3 are in parallel. What is the value of current flowing thru R2 if the voltage supplied is 10 volts and if the resistors are al identical with value of 10 ohms.
Given the circuit below, determine the voltage drop across the resistor R1. The source is 10V, R1= 2k ohms and R2= 3k ohms.
Circle. For the circuit shown below, find I1, 12, 13: 1 2. Voltage across each resistor. 3. Disconnect the sources of voltage. Rtotal and select *
Parts 4 and 5 please.
For the circuit shown, what will be the value of Rl to get maximum power? What is the maximum power delivered to the load?
Given the circuit below with VO = 20V, R1 = 6 ohms, R2 = 5 ohms, and R3 = 20 ohms, R1 VO + R3 Question 4: Find the voltage across R1 using voltage division. Be sure to select your answer in the quiz anc a. 12 V b. 8 V c. 4 V d. 3 V e. Write in your answer Question 5: Find the current through R1. Be sure to select your answer in the quiz and show how you arrive at the www R2
5. A nonstandard set-up was used for a resistivity survey as figure below shows. If the measured current was 0.997 A, voltage DV = VP1 - VP2 was 3.08 V, what was the apparent resistivity? C2 C1 256 m 16 m 178 m 49 m, P2 231 m P1
Home workin @1] Two resistors must be selected. So that the current in one is four. times the current in the other. It their equissalent parallel resistance is 5KM, calculate R₁ and R₂.. [Ausz 6-25k, 25k]
Step 5: Calculate the voltage across resistor R6 (VR6) [mV]. Use the resistance values from step 3 as follow R5 = 211.51ohm andR6 = 1420.86ohm. For the calculation of VR5 close Switch 1 and leave Switch 2 open. For the calculation of VR6 close Switch 2 and leave Switch 1 open. Use the circuit diagram of figure 1. Step 6: Calculate the maximum power absorbed by resistor R5 (PR5)[μW] and the maximum power absorbed by resistor R6 (PR6) [μW]. Use the resistance values from step 3 as follow R5= RTh(a,b) and R6 = RTh(b,c). Vs = 1.5V R1 = 4700ohm R2 = 2200ohm R3 = 6800ohm R4 = 2700ohm VR2 = 0.253V VR4 = 0.311V VR5 = 254mV
Given two batteries: one with voltage V and internal resistance r1; another with also voltage V and internal resistance r2. Which of the following is true if we connect them in series facing the opposite direction? No voltage will remain, while the total internal resistance will be r1 + r2. The total voltage will be -V, while the total internal resistance will be r1 + r2. The total voltage will be -2V, while the total internal resistance will be r1 + r2. The answer can be found on the other choices.
If the resistance of wires is taken into concideration, will the voltage across each wire be the same? and why ? this voltage depend on ?