Calculate the current across the capacitor shown in Fig. P8.6 if the voltage input is v1(t)=50 cos (152t+151°) V D(1) i(t) TC=1pF Figure P8.6 For a current i(t) = C cos(wt+P), enter the value of the phase angle (P). (be sure that your answer is between -180deg to 180deg.) Notes on entering solution: Enter your solution in degree . Remember the current should have a positive value . Do not include units in your answer .ex. 5° is entered as 5

Calculate the current across the capacitor shown in Fig. P8.6 if the voltage input is v1(t)=50 cos (152t+151°) V D(1) i(t) TC=1pF Figure P8.6 For a current i(t) = C cos(wt+P), enter the value of the phase angle (P). (be sure that your answer is between -180deg to 180deg.) Notes on entering solution: Enter your solution in degree . Remember the current should have a positive value . Do not include units in your answer .ex. 5° is entered as 5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The diagram below represents the phasor diagram for an RLC circuit using an 82.0 2 resistor, and unknown capacitor and inductor. Given AV₁ = 26.0 V, AVR = 21.5 V, and AVC= 17.5 V, determine the following. AVL AVC A Vmax (c) the average power delivered to the circuit W AVR (a) the maximum voltage and the maximum current V AVmax= Imax= A (b) the phase angle
Find the phase relation for the following pairs of sinusoids, (which leads and lags which by how much). Draw the phasor diagram e1= -20sqrt2 sin(377t + 200°) V e2 = -10sqrt2 sin(377t - 285°) V
P 8.3-21 The circuit in Figure P8.3-21 is at steady state before the switch closes. Determine an equation that represents the capacitor voltage after the switch closes. t = 0 10 18 V 25 mF v() 40
16. Two capacitors, a 20 µF and a 30 µF, are connected in parallel to a 400-Hz source. What is the total capacitive reactance? a. 7.96 Q b. 33.16 2 c. 42.04 2 d. 53.05 N
For the following pairs of sinusoids, determine which one LEADS and LAGS by how much.(draw the phasor diagram) a). e(t)=13.928cos(2t-21°)and i(t)=15cos(2t-11°) b). e(t)=20 sin (wt+50°) and i(t)=60cos(wt=10°) c). e(t)= 311 sin (2500t+120°) and i(t)=15.5sin(2500t-165°)
2. Explain which of the following instructions are invalid? State the invalidation reason and give the correct form for invalid instructions: a. MOV DL,AX b. MOV ES,CX c. MOV [BX],[2000] d. MOV BX,[AX] e. MOV CL,[BL+200] f. MOV 1234,DX g. MOV CH,[BX+SI+300] h. MOV DS,[SI+DI-5] i. MOV [4500],1234 j. MOV 200,[300]
The equivalent circuit for the measurement system is shown in the below figure, an oscilloscope having an input resistance of 40MSQin parallel with 8pF capacitor is connected across circuit an effective output resistance of Zo = 80k2. if the open circuit voltage has 1.75V peak for a 2kHz sinewave determine the value of voltage indicated on the oscilloscope when the frequency is: 1) 2kHz. 2) 50MHZ. 3) State your condusion from your results, what is the effect offrequency on the error value? Oscilloscopey Zo Voltage source Eo
8.50 In the phasor-domain R₁ = 1.2 k2, R₂ = 5 k2, C = 2 μF, and w = 1000 rad/s. *(a) Determine the power factor of the voltage source V. (b) Specify the capacitance of a shunt capacitor Cshunt that would raise the power factor at terminals (a, b) to 0.9 when connected between terminals (a, b). R₁ M circuit shown in Fig. P8.50, L₁=0.8 H, L₁= 0.6 H₂ b L1 ell Cshunt ell L2 C Figure P8.50: Circuit for Problem 8.50. ww R₂
Ex. 1844. Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal voltage source has a frequency of 600 Hz. R=5 Ohms, L=2 milliHenry, C=4 microFarad, V=20sin(wt) volts. Solve for the capacitor steady-state phasor current and voltage. I(jw)=Aexp(jB), vc(jw)=Dexp(jE), IMPORTANT RESTRICTION: Express radian angles between [-pi/2,pi/2]. Solve for the capacitor steady-state time-domain current and voltage: i(t)=Fsin(wt+G), vc(t)=Hsin(wt+K) Ans: w,A,B,D,E,F,G,H,K all MKS units. ans:9
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage Vr and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 Q, Vcoil = 22.4 V, Vr = 20 V and V = 36 V, find the resistance and inductance of the coil. %3D