Calculate the crippling load for a column using Euler's theory for long columns, whose effective length is 4 m. Take modulus of elasticity as 'E' kN/m² and moment of inertia as 'I' m4. Consider that both ends of the column are fixed. 1. 0.500 m² El kn 2. 0.0255 m² El KN 3. 0.0625 m² El KN 4. 0.025 π² EI KN

Calculate the crippling load for a column using Euler's theory for long columns, whose effective length is 4 m. Take modulus of elasticity as 'E' kN/m² and moment of inertia as 'I' m4. Consider that both ends of the column are fixed. 1. 0.500 m² El kn 2. 0.0255 m² El KN 3. 0.0625 m² El KN 4. 0.025 π² EI KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.29 mm the values of elastic modulus for steel is 217 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
A bar is composed of a section of aluminum rigidly joined between the sections of steel and bronze, as shown in the Figure. Axial loads are applied at positions indicated. If P = 3000 lb and the cross-sectional area of the rod is 0.5 in^2 , determine the effort in each section. The figure is in the attached image.
The bronze bar 2.7 m long with a cross-sectional area of 415 mm2 is placed between two rigid walls. At a temperature of 8.1 °C, there is a gap Δ = 2.32 mm, as shown in the figure. Find the compressive force (in N) experienced by the bar at a temperature of 68.66 °C. Use α = 18 × 10-6 /°C and E = 80.71 GPa. Round off your answer to three decimal places.
A round steel shell with outer and inner diameter 12 mm and 8 mm, respectively, encloses a brass core (Ebrass = 96 GPa) with diameter 6 mm. The steel shell and brass core are initially 1 m in length. A load P is applied to both shell and core through a cap plate. Find the load P required to compress both shell and core by 0.20 mm.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.66 mm the values of elastic modulus for steel is 207 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = (in N) ii) Stress-induced in the top bar = (in N/mm^2) iii) Stress-induced in the bottom bar = (in N/mm^2)
The bronze bar 2.72 m long with a cross-sectional area of 496 mm2 is placed between two rigid walls. At a temperature of 8.61 °C, there is a gap Δ = 2.28 mm, as shown in the figure. Find the compressive force (in N) experienced by the bar at a temperature of 61.85 °C. Use α = 18 × 10-6 /°C and E = 80.84 GPa. Round off your answer to three decimal places.
The structure of a beam with single supports is supported by a pinned moment MA at end A, an inclined load FB applied at point B, and a uniformly distributed load of magnitude q1 on segment BC. Find the support reactions at joints A and C, then calculate the internal forces at the midpoint of BC. MA= 380 N.m FB = 200 N q1= 160N/m a= 3 m b= 2m
A steel bar of 30 mm * 30 mm square cross section is subjected to an axial compressive load of 300KN. If the length of the bar is 3m and E=200GPa find contraction of the bar.
A round bar of length L. modulus of elasticity E, and weight density y tapers uniformly from a diameter of 3D at one end to a diameter 2D at the other end. If the bar is suspended vertically from the larger end, find the elongation of the bar caused by its own weight.
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.1 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 6 mm. Consider a linear elastic behavior. Select one: P = 597 N P = 537 N P = 430 N P = 573 N P = 287 N
An aluminium alloy rod of length 1.8m and rectangular cross-sectional of area 250mm^2 is subjected to a compressive load of 45kN. Young's modulus and Poisson's ratio for the material are: E = 71 GPa and v =0.33. Determine the decrease in length and increase in area of the bar.
SHOW ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is stretched between 2 fixed supports. The tensile load at 20 oC is 5 kN. Use E = 200 GPa and  = 11.7 x 10- 6 /oC 1. At what temperature will the stress be zero?2. What will be the stress at - 20