Calculate the amount of lime required for softening 50,000 litres of water containing:H+=1.5 ppm, HCOB-=396.5 ppm., Mg+2=42 ppm, Ca2+=90.00 ppm and FeSO4.7H20=14uddThe purity of lime is 91%. (Consider molecular weignt H-=2, HCO3-=122, Mg+2=24, Ca2+ =40and FeSO4.7H2O=278)471.67 kg23.58 kgO 235.83 kgLime is not required for this sample

Composition of hard water sample : H+ = 1.5 ppm HCO3- = 396.5 ppm Mg2+ = 42 ppm Ca2+ = 90 ppm…

Calculate the amount of lime required for softening 50,000 litres of water containing: H÷=1.5 ppm, HCO3-=396.5 ppm, Mg-2=42 ppm, Ca2+=90.00 ppm and FeS04.7H2O=14 udd The purity of lime is 91%. (Consider molecular weight H-=2, HCO3-=122, Mg+2=24, Ca2+=40 and FeSO4.7H2O=278)

Calculate the amount of lime required for softening 50,000 litres of water containing: H÷=1.5 ppm, HCO3-=396.5 ppm, Mg-2=42 ppm, Ca2+=90.00 ppm and FeS04.7H2O=14 udd The purity of lime is 91%. (Consider molecular weight H-=2, HCO3-=122, Mg+2=24, Ca2+=40 and FeSO4.7H2O=278)

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

In the distillation of the mixture of acetic acid (MW=60.05 g/mole; d=1.05g/ml) and water (MW= 18.00 g/mole; 1.00 g/ml), a total of 0.028 Liters of 1.0 M std NaOH was used to reach the endpoint of a 23 ml of distillate. What is the mole ratio of the CH3COOH in the mixture? final answer in 3 decimal places.
You are asked to weigh 2 g of lithium and add it to 1500 ml of distilled water +2 drops of indicator, knowing that the density of water is 1 at room temperature while conducting this experiment. After determining the molarity of the LIOH, you need to know how many volume should be taken to reach the final concentration. Therefore, use the one underneath, so the molarity after dilution will be 0.025 M instead of 0.25 MAfter knowing the amount of LiOH, you need to dilute to prepare 0.025 M of LiOH in a 3000 ml solution. Show your calculation and units.
Calculate the final molarity of H2O2H2O2 if 1.3 mL1.3 mL of the 3.0% w/w H2O23.0% w/w H2O2 solution is diluted with 3.7 mL3.7 mL water, then added to 5.0 mL5.0 mL of a starch-iodide solution.
Ten grams of soil were displaced with 250 mL of 1 M ammonium acetate and made to a final volume of 1 L. Analysis of the final l-L solution showed 20 mg/L Ca, 2 mg/L Mg, 1 mg/L K, and 0.5 mg/L Na. Estimate exchangeable cations in meq/100 g soil.
1. Radii were reported as follows: Tit+ = 60 pm; 0²- = 140 pm. Based on this, tell as much as you can about the expected structure of TiO₂ - provide the hole type for the cation, the cell lattice, and the coordination numbers for both cation and anion.
How many liters of softened water, containing a sodium concentration of 4 * 10 ^ - 2 % sodium by mass, have to be consumed to exceed the FDA recommendation ? (Assume a water density of 1g / m * L ) Express your answer using two significant figures.
Why is the conductivity of mixture C larger than the conductivity of mixture A? C Mixture made by mixing equal volumes of 0.2 mol L–1 HCl and 0.2 mol L–1 NaCl Conductivity (mA) 340 PH 1 A 0.1 mol L–1 HCl 260 1
1- Calculate I (ionic strength) for a solution that is 0.5 molal in KCI and 0.2 molal in K₂Cr₂O7. 2- 1-When A = 1.05 × 10³ m², C(HCI) = 10.0 mol m³, 1=0.01 A for 200 s, x was measured to be 0.17 m. Calculate t (H¹) 3- Calculate the molar conductivities (A) of KCI solution (0.1 mol L¹), if the conductivity of this solution at 25°C is 0.012896 ¹cm¹. 4- Calculate the Molar conductivity of H (..).The lonic Mobilities of H* ions (u) is -36.23 x10*¹ cm² V¹s¹
Consider a solution that contains 0.10 M AsO43 and 0.15 M CO32. Solid Co(NO3)2 is added to separate these two anions. Ksp of Co3(AsO4)2 = 6.8 x 1029 and Ksp of COCO3 = 1.0 x 10 %3D 10 Assume the volume change is negligible. As solid Co(NO3)2 is added to this solution, which solid will precipitate first and what is the [Co2*] needed to maintain the maximum separation of AsO43 and CO32? COCO3 precipitates first and [Co2+]max = 9.1 x 10-7M COCO3 precipitates fırst and [Co2+]max = 1.9 x 10-9 M Co3(AsO4)2 precipitates first and [Co2+]max = 1.9 x 10-9 M None of these Co3(AsO4)2 precipitates first and [Co2*]max = 9.1 x 10-7M Co3(AsO4)2 precipitates first and [Co2*]max = 6.7 x 10-10 M COCO3 precipitates first and [Co2*]max = 6.7 x 10-10M