I need handwritten solution only otherwise skip note that 100 KN20 KN/m50 kN60°30ABCos30°= Sin60°=0.8663m10m2mSin30°= Cos60°=0.5calculate reaction forces

Hand written solution is provided below.

Answered: calculate reaction forces

Engineering

Mechanical Engineering

calculate reaction forces

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.18P: Repeat the previous problem using sx= 12 MPa.

See similar textbooks

Related questions

Q: 2-Express each of the forces in Cartesian vector form and determine the magnitude and coordinate…

Q: 2. The maximum tension that can be developed in the cord shown in Fig. below is 500 N. If the pulley…

A: Tension, T= 500 N Pulley at A is free to rotate. Coefficient of static friction at the fixed drums B…

Q: The assembly consists of two 15-kg bars which are pin connected. The bars are released from rest…

Q: Required information NOTE: This is a multi-part question. Once an answer is submittec Consider the…

A: P = 815 N

Q: Air contained in a piston-cylinder assembly undergoes the power cycle shown in the figure below. 3.0…

Q: *6-120. The scissors hoist is operated by applying a Force P to the roller support C using a…

A: In the case of equilibrium sum of horizontal forces is the sum of vertical forces is zero and the…

Q: *4-100. If the resultant couple moment acting on the triangular block is to be zero, determine the…

A: If the resultant couple moment acting on the triangular block is to be zero.Determine the magnitudes…

Q: Two 2 kg balls are attached to the ends of a rod. The rod is attached to an axle such that the balls…

Q: Determine the moment of inertia ly (m.“) of the shaded area about the centroid. Type your answer in…

Q: Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

Q: 4.) Determine the moment (scalar value) about axis AB from the cable tension force (T) exerted at…

Q: [3.] This problem investigates how an ideal fluid flows in a linearly tapered pipe. The radius of a…

A: Given Data: ideal flow in a linearly tapered pipe tapered pipe radius at location x is…

Q: The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in…

A: Given:Cable diameter = 4mmE =200 GPaMax Stress 190

Q: Need only handwritten solution only (not typed one).

A: The mass of A is The mass of B is

Q: 2. The cantilever footing is used to support a wall near its edge A so that it causes a uniform soil…

Q: Part A If h = 340 mm, locate the centroid y of the cross-sectional area of the built-up beam.(Figure…

A: h=340 mmTo determine:The centroid

Q: Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum tensile…

A: P = 8 kN

Q: NASA is sending a probe to Alpha Centauri and then to Sirius. A problem with the probe is noticed…

Q: Determine a general expression for the normal force NA exerted by the smooth vertical wall on the…

A: The mass of cylinder is .The mass of bar is .

Q: Ball B (10 kg) is on a rod on which a torque of M = (2t² + 4) Nm where t is in seconds. Fin the…

Q: PROBLEM 1 For the area shown, do the following: a. Determine the centroid with respect to the…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: An engine has a bore of 78mm, a stroke of 82mm, and a con- necting rod length of 168mm. The crank is…

Q: Figure -3 ft Figure -3 ft- < 1 of 1 M The bent rod is supported by a smooth surface at B and by a…

Q: In (Figure 1), the tension developed in cables AB and AC cannot exceed 450 lb. Part A Determine the…

Q: An object of mass 4 grams hanging at the bottom of a spring with a spring constant 5 grams per…

Q: Consider the yellow region that is bound by two straight lines and a circular arc in the xy-plane.…

Q: Required information Blocks A and Beach have 5.5 kg mass. All contact surfaces have the same…

A: Blocks A and Beach have 5.5 kg mass.All contact surfaces have the same coefficient of…

Q: If the brake ABC is applied such that the magnitude of force P varies with time as shown, determine…

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

Q: A rotating step shaft is loaded as shown, where the forces FA and FB are constant at 580 lbf and 290…

A: The force The Torque alternates from "O" The value of the design factor is 2.5.In the given problem…

Q: 4. If the maximum force that any member can support is 8 kN in tension and 6 kN in compression,…

Q: The circular disk of radius r = 0.25 m rotates about a fixed axis through point O with the angular…

A: The angular velocity is .The angular acceleration is .The radius is

Q: 8. Find the first moments of area and centroid of the following shape of uniform density. The circle…

A: The radius of cricle is

Q: In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of…

Q: 3.4-4 A solid circular bar ABC consists of two segments, as shown in the figure. One segment has…

Q: The couple M is applied to a beam of the cross section shown in a plane forming an angle 3 with the…

A: Given- M=110 kip-inDetermine- stress at points A and B

Q: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

A: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

Question

I need handwritten solution only otherwise skip note that

100 K
N
20 KN/m
50 kN
60°
30
A
B
Cos30°= Sin60°=0.866
3m
10m
2m
Sin30°= Cos60°=0.5
calculate reaction forces

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Can you explain how to calculate the reactions step by step?
TOS BASIC Determine the support reactions: 3 m 43.8 kN/m EM BY on {T -7.2 m- =0 +R 29.2 kN/m 222.5 kN -3.6 m- -3.6 m-
Please show your solution clearly thank you
3. Three bars each made from different materials are placed between walls when the temperature is 14°C. Determine the support reaction when the temperature becomes 19°C. The material properties are given in the figure. Answer: R = 3502.30 N Steel Brass Copper Ebr 100 GPa Ecu = 120 GPa Est=200 GPa ast = 12(10-6)/°C abr = 21(106)/C acu = 17(10-6)/°C Acu = 515 mm² |Ast = 200 mm² Abr= 450 mm² -300 mm- 200 mm- 100 mm 4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of 500 mm² with a = 16.8 μm/ (m°C) and E = 120 GPa. There is a gap of 0.18 mm between the slab and the aluminum rod. The aluminum rod has an area of 400 mm² with a = 23.1 μm/ ( mºC) and E = 70 GPa. Compute the stress developed in each rod when the temperature is raised to 85°C. Assume that the weight of the slab is negligible. Answer: OAI = 16.80 MPa 85 →TA Δ Copper Aluminum Copper 750 mm-
Previously submitted and received incorrect work through
Please solve this
Take P= 38 kN. EI is constant. (Figure 1) Figure -2 m P ▾ Part A ▼ Determine the y-component of the reaction at the roller B Express your answer to three significant figures and include the appropriate units. By= Submit Part B HA A₂ = Value Request Answer Determine the z-component of the reaction at the fixed support A Express your answer to three significant figures and include the appropriate units. μA Units Value ? Units ?
The true option
My answer here is R_av= 150 kN, R_b= 210 kN amd R_ah= 0 kN please verfy if my answers are correct
Given that: P+P = 6.0 kip 0.45x10^6 psi L1 = 20.0 in E = L2 = 15.0 in d1 = 1.25 in d2 = 2.0 in Then the reactions at A and C respectively in kps are: A - d1 L1 В L2 d2 RA = 0.9 kip, RC = 11.1 kip RA = 1.96 kip, RC = 10.04 kip O RA = 1.3 kip, RC = 10.7 kip RA = 2.7 kip, RC = 9.3 kip
I need help with part e, thanks
the expected answer is for I(1)= 1.43mm snd 12= 2.86mm LLLL 2 ]] ²/₂² A rod of negligible mass is attached to a wall by a frictionless pivot and supported by two springs as shown above. When the load W=0 the springs are unextended. Calculate the extension in each spring when a load W = 5 N is applied to the rod. The spring constant of spring 1 is 10³ N.m-¹ and that of spring 2 is 1.5 × 10³ N.m. The forces can be assumed to remain perpendicular to the rod. TOT reeeeey