(c) Your friend Lynn Year looks at this circuit and says this can be modeled as a voltage controlled current source. Since you are learning about this in 10A she comes to you for help in figuring it out. You model the circuit as shown in figure 9. You learned that to find g you need to incrementally move Vin and measure Ie (tastes like a derivative!). So what is the transconductance g, at the operating point? Hint: Think orders of magnitude and what you can ignore to make your life easier.

(c) Your friend Lynn Year looks at this circuit and says this can be modeled as a voltage controlled current source. Since you are learning about this in 10A she comes to you for help in figuring it out. You model the circuit as shown in figure 9. You learned that to find g you need to incrementally move Vin and measure Ie (tastes like a derivative!). So what is the transconductance g, at the operating point? Hint: Think orders of magnitude and what you can ignore to make your life easier.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need answer in your hand Design a buck-boost converter to supply a load of 100 W at 60 V from a 30 V source. The output ripple must be no more than 2 percent. Specify the duty ratio, switching frequency, inductor size, and capacitor size.
The input voltage of the Buck-Boost converter can vary between Vi = 20V - 50V. Output voltage is required to be Vo = 30V. Since the power transferred to the load is always P> = P min, calculate the critical value L for continuous current mode. (just write the result you calculated.) fsw Pmin 25 kHz 6W
Design the circuit to achieve the output voltage v0 given in the figure and scale the output voltage according to the input voltages given.
Q4
Determine Vo for the given OPAMP circuit. Assume ideal OPAMP. (use Kirchhoff’s Laws). An idealOPAMP has 0V differential input voltage. Meaning the negative terminal and the positive terminalare connected to ground and the resistance between the input and the output is infinite.
In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…
4- For an operational amplifier circuit below. Draw the input and output waveforms if Vin is sine wave with 10 mV,R₁ = 10 KM, and R₂ = 100 KM. VI R₂ www PO
In order to connect a LED to one of the pins: O You need to define that LED as an OUTPUT in the setup function O You need to define that LED as an OUTPUT in the loop function You need to define that LED as an INPUT in the setup function In order to control a DC motor from a computer: We need a DAC such that data will flow from computer to DAC and from DAC to DC motor We need an ADC such that data will flow from computer to ADC and a DAC so data flows from DC motor to computer We need an ADC such that data will flow from computer to ADC and from ADC to DC motor In order to light a LED: O send a HIGH signal and this will be written in the setup function send a LOW signal and this will be written in the Loop function send a HIGH signal and this will be written in the Loop function If you want an LED to blink: O You can connect it directly to one of the digital pins of the Arduino O You need a digital to analog converter between the Arduino and the LED O You can connect it directly to one…
An op-amp circuit has the following values: +V = 11V, -V = -11V, Av = 113. Assume that the load will not restrict the output voltage swing. The maximum allowable value for Vin in mV is ?
If I have an input sine wave in a peak detector circuit I know the output the the first op amp (that will feed back into the negative terminal) should be a little larger than the input (this is why you add a second op amp). I'm not understanding it graphically. Splitting up the circuit say you have the first op amp and the diode (no capacitor or second op amp). the output should be only the positive part of sine wave, and the amplitude will be the amplitude input minus .6V from the diode drop, right? Then adding the capacitor it keeps the same amplitude but makes more DC. with the second op amp this makes it so the capacitor doesn't discharge (which is what keeps the voltage proper up I think?) With my logic here, the voltage feeding back into the first op amp negative terminal is the voltage input, minus a diode drop. So Vin > V- (voltage feeding back into the negative terminal). Which I'm pretty sure V- is supposed to be larger. So I think I'm misunderstand something here. Please…
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
Design an analog circuit diagram to the following analog equation: V.= 0.35V1-5.24V2-4.5 Design an analog circuit diagram to the following analog equation: V. = -5V1+3.5V2+20V3+10