c) Identify the pin configurations of the dual 4-to-1 line MUX. Dual 4-to-1 line MUX Pin # (74LS153 IC) AAAAAAAE 10 11 14 15 16 8. 234O

Q: 7. Design 4-bit full parallel adder with look ahead carry generator. a. Drive and draw the look…

A: a. Design 4-bit full parallel adder with look ahead carry generator. Drive and draw the look ahead…

Q: B)-The following program generates a square wave on pin P2.0. Find the output frequency? MOV R6,…

A: Here, the delay I m considering is 1ms                                             Mov r6, #0Ah…

Q: Q1) Design än signa! through bit ! of port C: Perfod of 1 second Perlod of 0.5 second Write the…

A: Write the assembly program that generates the signal. Assume the crystal frequency of 1 MHz.

Q: b) Kmap Simpliffication :- un AB F = o'+B'c't A'B' d) Draw the simplified funetion using NAND gates…

A: Given function is  F= D'+ B'C'+ A'B'  Total 4 variables  Simplified function using NAND gates

Q: Design a 3 to 8 decoder using Verilog HDL and verify using a timing diagram

A:

Q: 8051 microcontroller C program to toggle only pin P1.3 continuously every 250 ms. Use timer 0, mode…

A: 8051 microcontroller has two independent timer which can be used as timer(to generate…

Q: Draw the truth table and determine the Functions for Carry Out and Sum of a full adder

A: As per guidelines, we are supposed to answer only one question. Kindly repost the other question as…

Q: b

A: indicate three path labelled (aabb ) and convert to DFA

Q: 2. Explain the function and purpose of different types of Tristate, construct 4:1 Mux using…

A:

Q: i- Describe an assembly program for PIIC18 to toggle all bits of PORTB, PORTC and PORTD every ½ of a…

A: 3) Assembly program is given below to create a square wave of 75% duty cycle on bit 0 of PORT C

Q: c) Identify the pin configurations of the following decoders. 3-to-8 line decoder (74138 IC) Pin # 9…

A: 1) The IC 74LS138 is a 3 to 8 line decoder, the main function of this IC is to decode and setup of…

Q: 4. Design equation F(A,B,C,D)=E(1,2,3,6,8,10,12,13,15) using a 4×1 Mux?

A: A 4X1 mux, also known as a 4-to-1 multiplexer, is a digital circuit that selects one of four input…

Q: Draw the timing diagram  4321H   LDA A607 H

A: Given:    Draw the timing diagram  4321H   LDA A607 H

Q: QUESTION 2 Write down a VHDL code that calculates the Two's complement of the binary number A, where…

A: the solution is given below :

Q: 1. Step 1 - simplify Boolean functions for the following logic devices. 1. 4X1 and 8X1 multiplexor…

A: Boolean functions refer to functions whose inputs and outputs are from a two-element set, typically…

Q: On our board the output signal on pin 8 of the LS04 is: IO/M ROMSEL WR ROMRD IORD RD

A: Answer:- The correct answer is "IO/M"

Q: 1) Choose the suitable from the table below for each shift operation:

A: Hi hi Given :

Q: Assume that the circuit in Figure 5.3 indicates an invalid code for binary 1000 and 1001 in addition…

A: The circuit contains three NAND gates, one OR and one NOT gate. two inputs are provided at the…

Q: Draw an 8 to 1 multiplexer which uses two of 4 to 1 multiplexer and a 2 to 1 multiplexer

A: b.  answer 4:1

Q: H.W. Design the interface circuit that make the interface between 8 switch and control 8 LED where…

A:

Q: c) Identify the pin configurations of the Octal Priority Encoder. Pin # 8-to-3 line Priority Encoder…

A: 1) 74LS148 is 8 To 3 Line Priority Encoder 2) It features priority decoding of the inputs to ensure…

Q: Design a 4 bit subtractur using (2 input NAND)

A: Design of 4-bit substractor using 2 input NAND gates shown below both in block wise and single unit…

Q: please design an unsigned shift-add multiplier in multisim

A: The question is solved in step2

Q: a) Express the number (+62)a as an 8-bit 2's complement form. b) Add the following BCD numbers:…

A:

Q: erive the 8-QAM output using the transmitter block diagram in the module of the following input: (a)…

A: : QAM is a combination of PSK & ASK                 PSK + ASK = QAM : To Make 8- QAM take 2…

Q: adder/subtractor

A: 4-bit adder It can be implemented with the help of a full adder, a single full adder adds two…

Q: 26 Q) Chose the Correct data input for (4 to 1 mux) that used to Design the Switching network F:-

A: choose the correct data input for 4-1 multiplexer that used to design the switching network F

Q: Q3: Assume you have a main CLK with frequency of 16KHZ, design a frequency divider circuit that…

A: A frequency divider  can be constructed from jk flip flops by taking the output  of one cell to the…

Q: Write C18 program to send a byte of data serially to RC2 pin from PORTB. (MSB should go last)

A: The answer is given in the below step

Q: (g) In 8051, which bits of the TCON register are function as (i) Start bits of the timers and (ii)…

A: TCON register in 8051 is an 8 bit special function register which is used to control timers…

Q: Draw an 8 to 1 multiplexer which uses two of 4 to 1 multiplexer and a 2 to 1 multiplexer

A:

Q: In the process of testing a 74LS283 4-bit parallel adder, the following logic levels were observed…

A: Process:In the context of computer science and software development, a process refers to an instance…

Q: Q6. Construct a code to generate a square wave of 100 Hz frequency on pin PORTB.2. Use timer 0, 16…

A: Solution:--   1)The given question has required for the solution to be provided with the help of the…

Q: Please design this in frizing/tinkercad

A: When the button is pressed the voltage will flow through the circuit and the output will show 5V…

Q: DTo design 12- bit GPR has four control signal S3S2S1SO , need to use 12 (16 -to -1 multiplexer ) 16…

A: General purpose Register the control unit able the ALU and the data memory to be able to read or…

Q: PICmicro A/D converter has been configure and the following register values are provided: ADCONO =…

A: The value in decimal read on ADRESH register is

Q: Write vhdl code for 4 bit universal shift sregister using d flip flop with control mode shown below…

A: 4-bit universal shift register that can perform right shift, left shift, and parallel loading.…