c) For an RLC circuit resonant at 900 KHz, the known components of the circuit are the following: a 10-ohm resistor and a 0.1-mH inductor. The circuit is connected to a 2 mVRMs ac source. Determine the voltage across each component, the quality factor and bandwidth.

Q: how many different signals each consisting of 7 flags hung in a vertical line can be formed from 4…

A: It is given that: Total number flags hung in a vertical line=7Total number of Red flags=4Total…

Q: In the TIA 568-B wiring standard, the colors white green and blue have the pins numbers and O 3 and…

A: In the TIA 568-B wiring standard, the colors white green and blue have the pins numbers

Q: Q) All type of indicating instruments are passive and Null type * От

A: solve above ques

Q: 'JQ Clock J clock K

A:

Q: Table 1-4 4-Bit Reflected Code Reflected code 0000 0001 0011 0010 0110 0111 0101 0100 1100 1101 1111…

A: The other two codes we ca use are Hexadecimal code Binary code

Q: All of the following statements about the TRIAC could be true except: OA. TRIACS are not used in…

A: TRIAC:- A TRIAC is a three-terminal AC switch that differs from conventional silicon-controlled…

Q: a. b. d.

A: A computer port is used as an interface between the computer and different peripheral devices.

Q: The full form of PIPO is

A: Given, PIPO

Q: I. QUESTIONS/PROBLEMS 1. How are plus and minus current signs determined?

A:

Q: QUESTION 29 Select all signals that are inputs for the 8088. Use the schematic for our board. OSC…

A: Consider the schematics of 8088 shown below,

Q: What is the Circular chart recorder with diagram

A: As the name suggest a circular  chart recorder records data. It records data on a paper disc that is…

Q: For redirection which response code series is used

A: Redirection messages ( 300 – 399 )

Q: Can you redo this again? I need step-by-step solution, like there should be Step 1, Step 2, Step 3,…

A:

Q: c) Given the changed lines of code below, answer the following questions. ANALOG_COMPARE_SETUP: LDI…

A: The given code is shown below.ANALOG_COMPARE _SETUP:LDI R16,0STS ADCSRA, R16LDI R 16, 0b00000000STS…

Q: The degree of precision of a quadrature formula whose error term is : f(4) (5) is 3 O 1 4 O 2

A: The degree of precision of a quadrature formula is in if and only if the error is zero for all…

Q: To run a motor in two directions, we have to use DPDT switch. Select one: O True O False

A: To change the direction of rotation of a DC motor we have to switch the terminal of the…

Q: Convert (11010001.0111)2 into Oct.

A:

Q: ALL FINAL ANSWER SHOULD BE ACCURATE TO 3 DECIMAL PLACES USE POSITIVE ANGLE EQUIVALENT, NOT GREATER…

A:

Q: 1 use direct subfarction on the following binary numbers: ☺ lloo- lool

A:

Q: Count Mounting method 15. From the information you have studied about the various electrical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Zero Flag explained in a few lines

A: In microprocessors and microcontrollors there required a status flag for every operation performed…

Q: In the TIA 568-B wiring standard, the colors white green and blue have the pins numbers O 4 and 1 3…

A: The correct option is 3 and 4

Q: can not read the the simplifying the positive feed back loop part

A:

Q: For the following circuit, values of QO, Q1 are only observed at select time indicated by the dashed…

A: At every +ve clock edge, D0 will change its output At every -ve clock edge, D1 will change its…

Q: Question 5

A: There are three types of buses-  Load bus Slack bus / swing bus Generator bus 1. Load bus- A bus…

Q: IC 5557

A: he G5517 includes a step-up converter, two charge pumps, and a high current operational amplifier…

Q: Can 60Hz noise be eliminated?

A: The solution is provided in the following section.

Q: Convert the OCTAL NUMBER 65 40.7 20 2 to decimal number. Answer = %3D

A:

Q: Where does 23/332 for N1/N2 come

A:

Q: Need help finding TF

A: Given: Block diagram of a control system. Formula and concept: Transfer function: Transfer function…

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: how are changes to sections of code from previous identified in the nec

A: Under the National Electrical Code (NEC), It provides the electrical safety in industrial…

Q: For the following circuit, values of QO, Q1 are only observed at select time indicated by the dashed…

A: The given circuit contains a D flipflop and the output of the flipflop is the same as the input…

Q: Display all the numbers from 20 to 1 using while loop.

A:

Q: The carrier signal is always an analog signal. an analog signal in case of an analog information…

A:

Q: What is a line refernce number in electrical prints

A: For developing the circuit diagram, it needs to be identified as the unique components. The…

Q: One method for turning off an SCR is called forced commutation * TRUE False

A: SCR: SCR is commonly known as Silicon controlled Rectifier. It has four junctions. SCR is turned on…

Q: The given system has accuracy.

A: Accuracy

Q: Compute 1100 1000)2- (1001 1111)2 and indicate whether there is a borrow or not at the end. O 0010…

A: Bartleby has policy to solve only first question and incase if it has subparts then solve only first…

Q: Asynchronous counter Using T Flipflop up counter mod (10) 0-9 ? counter using flipflop

A: As ethe guidelines, we are supposed to answer only first question. Please repost the remaining as…

Q: Identify the Electrical Symbol

A: Each electrical component is represented with a symbol in electrical drawing.