c) During his rotational throwing motion, a discus athlete increases his angular velocity from 3.9 radians per second to 21.6 radians per second in the period just before he releases the discus. The length of time over which this occurred was 0.8 seconds. What is the average angular acceleration of the thrower?

c) During his rotational throwing motion, a discus athlete increases his angular velocity from 3.9 radians per second to 21.6 radians per second in the period just before he releases the discus. The length of time over which this occurred was 0.8 seconds. What is the average angular acceleration of the thrower?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can u help me answer this, Thank you hehehe
For the following mechanism, if the length of rod AB, I = 1.9 m, and its angular velocity w = 7.1 rad/s, determine the magnitude of the linear velocity of point B. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. 0.5 m B 30° A 45° Your Answer:
The mechanism shown is composed of rod GPV pin-connected to rod DPE at point P. Knowing that the velocity of V is 4 m/s downwards, A. [20%] Redraw bar GPV and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances needed. B. [15%] Determine the angular velocity of rod GPV. C. [30%] Determine the velocity of point P. D. [20%] Redraw bar DPE and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances needed. E. [15%] Determine the angular velocity of rod DPE. NOTE: Use INSTANTANEOUS CENTER METHOD for Velocity Analysis
The motion of a robotic arm is described by polar coordinates: r= t3 e = cos (t) where t is the time in seconds. What is the acceleration in r-axis direction when t = 2 s?
kinematics of rigid bodies
Please can you answer with full working out and label each part
For items 4-5, consider the slider-crank mechanism shown. Crank AB is 0.500 m long. Rod BD is 1.500 m long. The velocity at point B is 0.500 m/s, ↖45.0°. Which of the following gives the closest value to the speed of the piston at D? Which of the following gives the closest values of the lengths of the sides of the triangle formed by points B and D and point C, the instantaneous center of rod BD?
TOPIC: KINEMATICS Specific Instructions: Solve each problem NEATLY and SYSTEMATICALLY. Show your COMPLETE solutions and BOX your final answer. Express your answers in 2 decimal places. Please write clearly.
2.) Garage door ABC slides horizontally at A, and vertically at B. At the position shown, point A is pulled to the right at 1.2 ft/s. Determine: a.) Location of the instantaneous center of rotation of the door. b.) Angular velocity of the door ABC (include direction). c.) Linear velocity of point B (include direction). d.) Linear velocity of point C (include direction). X ft 7 X = 20 Y = 10 Z = 24° Y ft B 00
Question 29 Not yet an A pulley, starting from rest, is given an acceleration of 0.5 rad/s.What will be its speed in r.p.m. at the end of 2 minutes? If it is uniformly retarded at the rate of 0.3 rad /s, in how many minutes the pulley will come to rest? B Enter your answer here.... hp
For the following mechanism, if the length of rod AB, I = 2.0 m, and its angular velocity w = 5.5 rad/s, determine the magnitude of the angular velocity of rod AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. 0.5 m B 30° A 45° Your Answer: Answer units
A 16-cm x 20-cm gas engine has a normal speed of 450 rpm. Determine a.) the speed, in rev/s and rad/s; b.) the linear velocity of the crank pin, in cm/s and m/s. If the engine is allowed to stop at a uniform rate in 3 minutes and 20 seconds, determine c.) the deceleration of the crank, in rad/s²; d.) the distance, in cm, traveled by the crankpin in coming to rest; and e.) the distance, in cm, traveled by the piston in coming to rest.