. 14 ksiC ):- Draw the Mohr's Circle of thestress element shown in figure.Find:-12520ksiA1)principle stresses.2)The maximum shearing stresses.3)The stresses acting on inclinedplane A-B with Y -axis.

Answered: Image /qna-images/answer/596c6cd3-a7e2-4eb6-b408-dbb66993d4de.jpg

Answered: C ):- Draw the Mohr's Circle of the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Manufacturing methods
4) At what temperature will Aluminum have 1017 vacancies per cubic centimeter.
Q1. Draw and explain five casting defects in sand casting process. briefly.
Home Work: Show that the true strain rate in extruding a round billet of radius ro as a function of distance x from the entry of a conical die can be given as: 2V,rž tana where; Vo: ram velocity (ro-xtana)3
There is a steel that has been rolled and you want to verify its mechanical properties, so two samples are cut, one in the direction of the rolling and the other perpendicular to it. In which case both samples have the same properties and in which case they are not the same.
Please I need answer with Details
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.
What is meant by Thicket and thinned? What is the difference in between both types? Note: Please do not handwritten and write short answer.
D. By using the following figure, suppose aluminum alloy and carbon steel have the same tensile properties, which metal will suggest to select working at low temperature? Why? fcc materials Low strength bcc materials High-strength materials Temperature Energy absorbed
Q3B) A metal is fabricated by drawing at 125 °C. The metal melting temperature is 400 °C. Find by calculation whether this foming process is cold or wam or hot working. Ans--
Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a) How much heat is generated? (b) What is the rise in temperature of the brass if 75% of the heat generated warms the brass? What happens to the other 25%? (don't change the hp, lb)
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

C ):- Draw the Mohr's Circle of the stress element shown in figure. Find:- 1) principle stresses. 2) The maximum shearing stresses. 3) The stresses acting on inclined plane A-B with Y-axis.