(c) Determine the output voltage of temperature measuring bridge circuit shown in Figure Q2(c) if the thermistor is exposed to a temperature of 50 °C. The thermistor resistance at 25 °C is 1.0 k2. Assume that the resistance of the thermistor decreases to 900 2 at 50 °C. (6 marks) Rehremiator 1.0k @ 25°C R2=1.0k2 V.-12V Vout R3=1.0k2 R-1.0ko Figure Q2(c) CS Scanned with CamScanner

(c) Determine the output voltage of temperature measuring bridge circuit shown in Figure Q2(c) if the thermistor is exposed to a temperature of 50 °C. The thermistor resistance at 25 °C is 1.0 k2. Assume that the resistance of the thermistor decreases to 900 2 at 50 °C. (6 marks) Rehremiator 1.0k @ 25°C R2=1.0k2 V.-12V Vout R3=1.0k2 R-1.0ko Figure Q2(c) CS Scanned with CamScanner

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using second approximation for a diode to calculate the load voltage.
half bridge given in the figure for the rectifier circuit; Output current and voltage waveform draw
In the circuit shown below, if VA= 1V and V-2V, the statuses of the diodes are (Assuming ideal diodes) D₁ VA V₂₁ D₂ ERL Vout Select one: O a D₂ is ON, D₂ is ON O b. None of these Oc. Dy is OFF, D₂ is ON O d. Dy is ON, D₂ is OFF
A 500 ohm resistor is connected to a 12V source at one terminal and a 10V zener diode of 250 mW and a 5K ohm resistor are connected to the other terminal. What is the maximum current of the zener diode?
3.- Suppose that each diode in the circuit shown in figure N°2 has a turn-on voltage of Vy=0.7 volts. Determine the value of Vo and Vi +5v 9.5k D1 +2v 0.5k V1 D2 No 2 +4v 0.5k w Fig. D3 D4 1k O Vo 0
A bridge rectifier shown below will have a positive pulsating voltage as its output, To convert the output to be negative, D . O a. D1 must be reversed b. D1, D2, D3 and D4 must be reversed O c. D1, D2 and D# must be reversed O d. D1 and D@ must be reversed O e. none of these
Determine the voltage across the resistor R2. (assume Zener voltage is 3 volts and Diode forward voltage is 0.7V)
Drow the Vin and the output Voltage of the half wave rectifier () and draw the circuit it?Vin=0.5 vp. pF=1 KHz
You are told that the approximate diode knee voltage is 750mV, but you need to know for sure. You are told that the diode's saturation current is I, = 2.27fA. (2.27x10-15 A) and V=25mV. Determine VD. Iterate until you have the answer to 2 significant figures.
A charging circuit that will deliver constant DC current will be designed. The input of the circuit is 220V / 50Hz AC and its outputIt will be 5V / 2A DC.The circuit will consist of 3 parts:AC transformer will reduce the voltage on the inputii. AC rectifier circuit will convert low AC voltage to DCiii. Current source, this part will keep the current at the output constant.You determine the transformer drop rate in the first part. Its output is low voltage ACas the source and design the second and third parts accordingly.