c) A thermistor resistance of 5 ka at the ice point (0 'C) and 800 n at 50 °C. The resistance temperature relationship is given by: R, - aR where: R = resistance at temperature T (in Kelvin) Ro = resistance at ice point (in Kelvin) a, B = constants i) Compute the parameter constants a and B. ii) Compute the range of resistance to be measured in the case of temperature variation from 60 °C to 100 °C. ii) From the result obtain in Q2(C)(i) and Q2(C)(i), illustrate the characteristic of the thermistor's resistance variation over temperature in °C.

c) A thermistor resistance of 5 ka at the ice point (0 'C) and 800 n at 50 °C. The resistance temperature relationship is given by: R, - aR where: R = resistance at temperature T (in Kelvin) Ro = resistance at ice point (in Kelvin) a, B = constants i) Compute the parameter constants a and B. ii) Compute the range of resistance to be measured in the case of temperature variation from 60 °C to 100 °C. ii) From the result obtain in Q2(C)(i) and Q2(C)(i), illustrate the characteristic of the thermistor's resistance variation over temperature in °C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You are to design a simple power supply made up of recycled electrical parts to drive a motor. To simplify the design, you can model the running motor as a load resistor. The motor is rated for 20V and draws 100mA when running. 120Vrms Resistor 60HZ Vp Vs 0° + C1 1250pF a = 3.75 Zener "Motor BR805D а. If you were to model the running motor as a resistor what would the resistor value be? b. The transformer has a turns ratio a = 3.75. What are the RMS and Peak values of the secondary voltage? What is the peak voltage after the diode rectifier bridge (without C1, Zener, resistor, or load)? Draw the waveform. d. Determine the ripple voltage (VRIPPLE) without the Zener diode in the circuit (assume the Resistor above is 1002). Determine the part number of a suitable Zener diode to provide an output voltage of approximately 20v. (i.e. 1N4 C. е. 2.
Q/ A.C. voltage with peak value (Vm 20V) is connected in series with silicon diode an and load (R-500 £1) If the resistance of the diode-10 12, calculate: www -20V+ (1) diode current (2) output voltage Repeat (1&2) if the diode is to be ideal. +20V S00 a -20V
The diode shown in Figure T9.2 is ideal. Determine the state of the diode and the values of vx and ix.
4) For single-phase half-controlled bridge rectifier shown in the figure : 1. Derive a formula for mean load voltage. 2. Draw the waveforms of Vosis w i3, ių and io assuming highly inductive Load and <=45°. T, 12
For the given circuit find the VRL Voltage of the load; VR Voltage in the resistance R; Iz Current of the Zener diode and the Pz Power in the Zener diode. VRL = ? Iz = ? Pz = ? If the Zener diode in the figure has an elbow tension of 0.7 V. Zener breaking voltage of VZ = - 15 V Vin = 40 V R = 1 kohm RL= 3 kohm Requirement: Take out Vth by mesh method and solve equations
2) In the circuit given in the figure, R = 6k2, Zener diode breakdown voltage VZ = 3.6V and www mm w wwm w Zener diode power value is given as 6.5mW. wwm the maximum diode current that can flow through the www w m m w mw ww m w ww md w m circuit, Calculate the maximum voltage value that can be applied w w mww m w w m www m w mentn Vz=3.6 v A to the circuit without damaging the diode. wm w w ww m ww
Solve Problem 2
Apply each of diode approximations given the following parameters: D1: Si, rB = 2 Q, rR = 220 kQ D2: Si, rB = 5 Q, rR = 560 kQ and determine the current flowing through D1, D2 and R2, R3, the voltage across R3. Finalize answers as follows: Ideal approx: Id1= Id2= 12= , 13=_ V3= ; 2nd approx: Id1=_ Id23D 12= 13= V3= : 3rd approx: Id1=_, Id2= 12= 13= V3= R1 2.5 ka D1 D2 R3 10 V 2.5 ka R2 1 ko
Using 2nd approximation for the circuit shown, assuming that the diode used is a silicon diode, determine the currents ID1, ID2 and current through R2. Finalize answers as follows: ID1= Ir2= ID2= R2 D1 3.3 kQ BAT1 D2 20 V R1 5.6 kn
1. You are to design a diode clipper circuit that will keep high voltage spikes from a 'noisy power supply from reaching sensitive electronics. A conventional silicon diode is used as part of the design. The clipper circuit is to be designed so that voltages 2 Resistor 10 volts are 'clipped'. SI Diode Vin from noisy Vout to electronics a) What would a suitable Zener breakdown voltage be? source Zener Diode b) From the manufacturer's specifications sheet, what would be a good choice for the Zener diode (i.e. what part number? 1Nxxx)? Why? c) If you want to 'clip' voltages that are s-10 volts as well, show how you would modify the circuit.
Electric Current and Resistance. What is an Electric Battery? Define electric current and state what is meant by the term conventional current. Describe Ohms's Law and draw an example using an I-V cuvre.
For circuit given in Figure 3 use Complete Diode Model andfind the voltage across R1 and R2 andtotal current flowing in this circuit. Giventhat diodeforward resistance is 15 Ohmsfor D1 and 10 Ohmsfor D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 Q ww D2 Rz100 N KH 10 V R3150 2 www Figure 3