(C) A plain sided specimen is subjected to 2 * 107 cycles at the applied stress range of 100 MPa. Estimate how many further cycles can be applied at a stress range of 400 MPa before failure is predicted to occur.

(C) A plain sided specimen is subjected to 2 * 107 cycles at the applied stress range of 100 MPa. Estimate how many further cycles can be applied at a stress range of 400 MPa before failure is predicted to occur.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cylindrical specimen of brass that has a diameter of 21 mm, a tensile modulus of 122 GPa, and a…

A: Given that , Diameter of cylinderD=21mmModulus of elasticityE=122GPaPoission's ratioμ=0.37Tensile…

Q: A specimen of a 4340 steel alloy having a plane strain fracture toughness of 45MPa√m is exposed to a…

Q: A steel plate, which has a fracture toughness in a plane strain state of 83 MPavm, is alternately…

A: Given Data: KIC=83 MPamσmax=750 MPaσmin=20 MPaf=1n=2.8ai=0.0015 mm To Find: Determine the value of…

Q: A three-point bending test was performed on an aluminum oxide specimen having a circular cross…

Q: between a ductile and brittle material and the concept of ductility and its measurement. b)A…

Q: Determine the indentation diameter of a mild steel material subjected to a Brinell hardness test…

Q: elongations is 1.0 mm. The total length of the test specimen after 4,000 hours is 105 mm. If the…

A: To obtain the solution of the above question, first of all, we will determine the creep rate of the…

Q: Uniaxial yield stress of a material is 420 MPa Determine shear yield stress using Von Mises…

Q: What minimum specimen diameter is required to ensure

A: Given datathe three-point transverse bending test,the square section of side a= 18.5 mm= 0.0185mThe…

Q: Answer the following questions concisely (no more than half a page per question): a What do you…

A: b)

Q: In a tensile test, the force at the yield point was 1000 KN, at the ultimate point was 1500 KN and…

A: Given data: The yield point load on the specimen is Fy=1000 kN The ultimate point load on the…

Q: An 820 MPa (145,000 psi) stress is applied to a specimen of 4341 steel alloy, which has a plane…

A: Given Data

Q: A tensile test for a copper specimen has been performed and the following data are obtained. -…

A: Given data: The percentage of elongation, %L = 60%. The percentage of reduction in area, %A = 36%.…

Q: A circular shaft of 20 mm diameter subjected to tensile load showed that 32% reduction at fracture…

Q: A high-strength steel was subjected to a tensile test. It failed under a stress of 1600 MPa with a…

A: given : σf=1600 MPaε=2.7%=0.027E=200 GPaσy=1400 MPa

Q: For an aluminum structure with a fillet radius of 0.07-in, the ultimate tensile strength is 60 ksi.…

A: Givenr=0.07inσult=60ksiq=0.8kt=2.1

Q: When an aluminum tensile sample with an initial diameter of 12.827 mm was tested, a maximum load of…

A: Given Data ⇒ Maximum load(F1)=66.72 KN Engineering strainε1=0.4 Engineering strainε2=0.2

Q: . In a tensile test of a cylindrical specimen with an initial diameter of 12 mm, the loads at 15 and…

A: Given…

Q: A mild steel tensile specimen of initial length 44 mm and initial diameter 6.4 mm is subjected to a…

Q: Can the maximum normal stress theory or Mohr’s failure criterion be used in practice to predict the…

Q: Will fracture occur for a material exposed to a tensile stress of 900 MPa if the material has a…

Q: Uniaxial yield stress of a material is 350 MPa Determine shear yield stress using Von Mises…

Q: 2. Mild Steel is tested in the laboratory. The data obtained are: Length of Specimen = 320 mm/…

A: Given Data: Length of specimen L1=320 mm Diameter of Specimen d=30 mm Load F=20 kN Elongation under…

Q: A fatigue test was conducted in which the mean stress was 58 MPa and the stress amplitude was 225…

A: Given conditions, Mean stress σmean=58 MPa. Stress amplitude σamplitude=225 MPa.

Q: A structural component in the shape of a flat plate 24.2 mm thick is to be fabricated from a metal…

A: Given data :- Thickness of plat = 24.2 mm Yield strength = 537 Mpa Fracture toughness = 28.2 Mpa√m…

Q: For a point on a steel specimen, the principal stresses are calculated as 1 = 200 MPa and 2 = -40…

Q: A tensile test for a copper specimen has been performed and the following data are obtained. -…

Q: The R-ratio (minimum stress to

A: Given data; Determine the R ratio for this cyclic loading.During a high cycle fatigue test, a…

Q: A specimen of a 4340 steel alloy having a plane strain fracture toughness of 45MPa√m is exposed to a…

Q: dimensions. Here, l=30 cm and the diameter is 4 cm. A Calculate the level of the tensile strength…

A: To given that,Pf(v)=0.1Pf(v0)=0.01module,m=9a we know that , P=1-e-(σσ0)m…

Q: A three-point bending test is conducted on a cylindrical specimen of aluminum oxide (E-400 GP2, Kım4…

A: The behaviour of the material under different loads is bending test. Given data;- Aluminium oxide,…

Q: A tensile test for a copper specimen has been performed and the following data are obtained. -…

A: Write the given data with suitable variables: %∆L=60%%∆A=36%Lf=35.2 mmdf=3.54 mmσut=439 MPa

Q: B/A cylindrical piece of carbon-steel with dimension of 100 mm length and 10 mm diameter exposed to…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

(C) A plain sided specimen is subjected to 2 * 107 cycles at the applied stress
range of 100 MPa. Estimate how many further cycles can be applied at a stress
range of 400 MPa before failure is predicted to occur.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Attempt only if you are sure Urgent.
Is the maximum normal stress theory useful to predict the accurate failure of brittle material?
A steel bar which is 457 mm long is repeatedly loaded with 4500 kg in successive tension and compression cycles . Calculate the minimum diameter of the bar which will never fail by fatigue. Given yield point=300 MPa, UTS= 400 MPa , fatigue limit = 306 MPaand Elastic Modulus = 210 GPa
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 66 % - Percentage of Reduction in Area = 38 % - Final length after fracture = 34.6 mm - Final Diameter after fracture = 4.43 mm & - Ultimate stress = 364 1) Final Area (in mm2) = 2) Initial Area (in mm2) = 3) Ultimate Load (in N) =
Help me please
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 69 % - Percentage of Reduction in Area = 39 % - Final length after fracture = 35.5 mm - Final Diameter after fracture = 3.6 mm & - Ultimate stress = 396 MPa SOLUTION: iv) Initial Diameter (in mm) = v) Ultimate Load (in N) =
3. A rod-shaped MgO specimen with round cross section is tested with the three-point bend method. What is the calculated minimum radius without fracture if the applied load is 5560 N, the flexural strength is 105 MPa, and the separation between the two support pins is 45 mm?
A material with an Ultimate Tensile Strength (UTS) of 400 Mpa is loaded cyclically about mean stress of 80 MPa. If the stress range that will cause fatigue fracture in 100 000 cycles under zero mean stress is (+,- )60 MPa, what stress range (in MPa) about the mean of 70 MPa will give the same life
Describe ductile fracture and brittle one. what is the difference between them in tensile test specimen, Explain in detail.
A cylindrical specimen of brass that has a diameter of 15 mm, a tensile modulus of 120 GPa, and a Poisson’s ratio of 0.30 is pulled in tension with force of 50,000 N. If the deformation is totally elastic, what is the approximate strain experienced by the specimen?
Qu2. (A) What is fatigue? Mention the sequence of steps involved in fatigue of a smooth specimen. Mention Four (4) factors that affect fatigue of smooth specimens, stating how each affects fatigue life (B) A very wide panel made of a material of plane-strain fracture toughness of Kic=55MPaVm was found to have a central crack of size 2.5mm. It is subjected to cyclic loading at a design (or working) stress of 690MPA and stress ratio of zero. (a) Sketch the stress-time graph of the loading cycle and determine (i) Stress Range, (ii) maximum cycle stress, (iii) stress amplitude and (iv) mean stress (b) Will the initial loading cycle cause the panel to fracture? Why or whynot? Compute the maximum allowable fatigue flaw size that can fracture the panel during the cyclic loading. (Assume that plain strain condition prevails). (c)