urgent in one hour (Please provide your final answers here, and also the same answer with your detailed reasoning on the PDF file tIn the following beam structure:• EI – 9000 kN.m?• L= 11 m• q = 20 kN/mВCADL(Note: Please provide all the numbers as ratios, do not use decimal points. For example, use 1/3 instead of 0.33)1. Determine the reaction forces (input magnitude only):Vertical force at A = 220Horizental force at D = 0kNkNMoment at D = 1210kN.m

Free body diagram - Vertical force at A = RA For the sum of vertical force - ∑My = 0⇒RA - 20×11 =…

C A D (Note: Please provide all the numbers as ratios, do not use decimal points. For example, use 1/3 instead of 0.33) 1. Determine the reaction forces (input magnitude only): Vertical force at A = 220 Horizental force at D = 0 Moment at D = 1210 |KN kN kN.m

C A D (Note: Please provide all the numbers as ratios, do not use decimal points. For example, use 1/3 instead of 0.33) 1. Determine the reaction forces (input magnitude only): Vertical force at A = 220 Horizental force at D = 0 Moment at D = 1210 |KN kN kN.m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: (a) CBR of a high quality well-graded crushed stone base course materials: and “Modulus of subgrade…

A: Note- Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: A circular plate of radius 0.75 m is vertically placed in water such that centre of plate is 2 m…

Q: Using the method of components calculate the magnitude, direction, and location of the total force…

A: Given:- H=20m specific weight of water =1t/m3 specific weight of concrete=2.6t/m3 To find:- a)…

Q: Calculate the mass of water needed to saturate a 1m' volume of soil that has a water content of 4%…

Q: In terms of w, L, E, and I, determine the deflection and slope at x = L of the beam shown in Figure…

A: Draw the free-body diagram of the beam.

Q: Calculate the diameter of a 32000-meter- long pipe if it is equivalent to a pipe with a diameter of…

A: Given, Length of pipe (1), L1= 32000m Length of pipe (2), L2= 1000m Diameter of pipe (2), D2=…

Q: Draw a schematic flow diagram showing processes to treat: (a) Groundwater containing dissolved…

A: (a) Groundwater containing dissolved solids of about 2200 mg/L with hardness around 250mg/L as…

Q: For a road with a distance = 3 km. Calculate (TMS) AND (SMS) for the following traffic. car Time…

Q: What is the prestress steel loss from steel relaxation at 356 days for a Grade 270 low-relaxation…

A: Given:- Initial stress = 190,000 psi Yield stress = 245,000 psi Time period = 356 days To…

Q: Problem 2 Consider the beam-column shown. Determine the lightest W10 section that can support the…

A: The beam column is basically subjected to the horizontal and vertical set of external loading…

Q: Determine the magnitude of the resultant force acting on the hook in N if F 430 N and F= 260N 30° 30…

Q: Determine the internal forces in member ABC at point J

A: The axial force in the member ABC is given by: AABC=400cos50=257.115 N The shear force in the member…

Q: The solid cylindrical rod BC of length L = 600 mm and radius r= ever AB of length a = isplacement of…

Q: Given data for column D = 350 Kips, L=250 Kips, 20 in x 20 in, 8#8 bars, fy = 50 ksi, f= 4 ksi, and…

A: The given data is shown below: D=350 kipsL=250 kipsSize of column=20 in.×20 in.fy=50 ksif'c=4…

Q: The door is kept open by means of two chains. If the stresses in AE and DF are FA N and FD = 500 N,…

Q: u = -c(y² + væ), v = 2cxy |

A: Given:- u=-c(y2+vx) v=2cxy c=constant v=Poisson's Ratio To find:- stresses

Q: Draw a flow diagram of a primary wastewater treatment plant. How does this process compare, if at…

A: Draw a flow diagram of a primary wastewater treatment plant. How does this processcompare, if at…

Q: A 220 lb force A and a 500 lb force B act on a bracket as shown. Their resultant is C. In the…

Q: A roof system consists of W14x30 beams with a span of 12 ft and a tributary area of 144 ft?. The…

A: The dead load is D=45 psf. The snow load is S=27 psf. The rainwater/ice load is R/I=34 psf. The wind…

Q: A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN. Neglect the…

Q: The given bridge truss supports point loads of 200kN at joints B, D, F, H, and J. The structure is…

Q: · A cantilevered beam is part of an assembly machine and is made of steel with round cross section…

A: Given 400lbf= 1780N

Q: 51. The structural concrete slab panels can be repaired by A. O Internal bonding B. O External…

A: Repairing the structural concrete slab panels is possible.

Q: 20 kN/m 11 kN U 20 kNm -Hinge A6.5 m 4.5 m73.5 my Draw the shear force-bending moment diagram of the…

A: GIVEN BEAM

Q: Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored…

Q: For the given beam: (a) Which of the following is the vertical reaction at C. [Select] (b) Which of…

Q: A reinforced concreté simply supported beam has a span of 5m and carries uniformly distributed dead…

Q: Describe the difference between the fracture behavior of hardened cement paste, mortar, and concrete…

A: Fractured surface of cement and mortar specimens were characterized using a confocal microscope to…

Q: After graduation, you worked in a wastewater treatment plant (WWIP). Your facility feeds chlorine at…

A: Given data- Requirement of Chlorine for various purposes is given- (1) 200 gallons/day for contact…

Q: 3. A hollow square cross section consist of an 8 in. x 8 in. square which is subtracted a…

Q: Complete the following table and draw the Soil Gradation Curve for the given soil. Calculate Cc and…

A: The given table is shown below: Sieve Amount retained (g) Cum Amount Retained (g) Cumulative %…

Q: A solid shaft (r=10 mm) made of two materials is inserted into two rigid walls at A and C. Shaft AB…

A: Given,Gs = 70 GPa = 70×103MPaTorque at interface between both metal, T = 100 Nm = 100×103 NmmAngle…

Q: The figure below shows a manometer connected to a pipeline containing oil of specific gravity 0.8.…

Q: An essential 5-story facility structure is conceptualized with an intermediate reinforced concrete…

Q: An irrigation pump delivers water through a 140mm horizontal pipe flowing full at the outlet, the…

Q: Classify the following soils by the (1) USCS and (2) AASHTO classification system and give the group…

A: AASHTO soil classification system is based on, Grain size distribution Atterburg's limits…

Q: Surveying Find the F.B. of the following lines from their B.B. - Line AB=N 50° 30' E, Line CD=S40°…

A: Given data, BB of Line AB=N 50° 30' E, BB of Line CD=S40° 30' E Every line has two bearings namely…

Q: QUESTION 14 A non-potable water storage tank is at an elevation of 37 feet above the discharge for…

Q: A ride in an amusement park consists of a rotating arm AB having a constant angular velocity wAB = 2…

Q: An oil of viscosity 0.5 N s/m2 and relative density 0.6 is flowing through a circular pipe of…

Q: Find the support reactions and the forces at hinge of the plane frame system given in the figure.…

Q: 1- For the structure shown, calculate bearing reactions and maximum moment and shear if w= 42 lb/ft…

A: step 1-

Q: In the entrance of car parking, the vehicle arrival in each Counting period of 100 sec. is shown in…

A: The given data: Vehicle per 100 sec Frequency 0 60 1 28 2 16 3 8 4…

Q: A3 meter high W14 x 43 columns in a 5-Story steel braced frame is pinned at the top and bottom and…

Q: = An industrial operation produces 80 mm diameter particulates (pp 1.5 g/cm³). Assume these are…

A: Given Dtata- An industrial operation produces 80 mm diameter particulates (p) = 1.5g / c * m ^ 3)…

Q: (3) ) A 6.0 m long simply supported beam is made of HN450×200×8 X 12, Q345steel. The beam carries on…

A: ALSO GIVEN CODE REQUIREMENTS FOR BENDING MEMBERS WITH CONTIOUS LATERAL SUPPORT IS AS BELOW:

Q: Determine the force in each member of the loaded truss. Th 2250 N -189m h-38m A- 46° F

Q: 2. The rated speed of a banked highway curve of 250-meter radius is 60 km/hr. If the coefficient of…

Q: A 2.5m thick fill is to be placed on a site underlain by medium clay. Given are the following: Yriu…

Q: Using the method of joints, calculate the force in each member of the trusses shown. State whether…

A: To find force in members

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

urgent in one hour

(Please provide your final answers here, and also the same answer with your detailed reasoning on the PDF file t
In the following beam structure:
• EI – 9000 kN.m?
• L= 11 m
• q = 20 kN/m
В
C
A
D
L
(Note: Please provide all the numbers as ratios, do not use decimal points. For example, use 1/3 instead of 0.33)
1. Determine the reaction forces (input magnitude only):
Vertical force at A = 220
Horizental force at D = 0
kN
kN
Moment at D = 1210
kN.m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.