(c) A 100-L container is filled with 1 kg of air at a temperature of 27 °C. What is the pressure in the container? (d) For the ideal diesel cycle, what is the cutoff ratio?

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the x-axis (θx)? Note that…

A:

Q: If an object is hanged by a string, the line of action of the string will not always pass through…

A: When an object is symmetrical then line of action of string passes through the centre of gravity of…

Q: Find reaction at A.

A:

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: Write the number of limbs, determine the degrees of freedom and draw the kinematic chain.  b)…

A: As valve engine is given where we are to find 1st number of links and number of higher joints and…

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: The weight will always act downwards at an angle of 30 upwards at an angle of 60

A:

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?

Q: find closure Eq.

A: You have mentoned the postions and angles .

Q: The figure shows a shaper machine that uses Whitworth quick return mechanism wherein the different…

A: Given Data OA=75cm OP=50cm CA=150cm CD=135 cm

Q: For the bearing shown below in the figure which of the following represents the bearing bore? For…

A: This question is based on the concept of deep groove ball bearing.

Q: y h с b bh .1

A:

Q: raw kinematic diagram of the drawing mechanism. etermine degrees-of-freedom of the drawing…

A:

Q: Chains are used in gears applications while belts are used with pulley systems. Select one: O True O…

A:

Q: Please do #5

A: Given AB+CD=X

Q: Not yet answered The toggle mechanism shown (Figure below) moves from an initial angle e = 30° to a…

A:

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: The engine room of a freighter is on fre A frefghting tugboat has drawn along sde and is drecting a…

A:

Q: Given the left and front views, sketch the top view.

A: The problem is easily done with the help of orthogonal projection. first try to imagine the 3D view…

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: Get a kinematic diagram (schematic view) equivalent to the following mechanism and its degree of…

A:

Q: The impending motion is applied when the body is Select one: O a. Just stopped Ob. Stopped Oc. Just…

A:

Q: 8. Three ships A, B, C are located as follows: A is 48 km due north of B and C is 125 km due east of…

A:

Q: SHAFT KEY

A:

Q: For the following mechanism, determine the degrees of freedom. 10" 6" 10" 6" 10"- 4" Crank 3"

A:

Q: Respond with TRUE if the symbol of the valve shown below is drawn corectly 2. 3 MI 4 15

A: Hydraulic symbols give a clear representation of the work of each pressure-driven component.…

Q: Get the degree of freedom of the following mechanism. Pin in Siot

A: Degree of freedom for the following mechanism

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: What is the meaning of + S.F, -S.F, +B.M and ?- B.M

A: There are sign convention for shear force and bending moment.  The shear force at a cross-section is…

Q: Please do #4

A: Given ABC=X

Q: What are the parts of Milling Machine  (Make sure the parts are labeled accordingly)

A:

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: A Before Ater False True O

A: Suppose Mass of Ball (A) = Ma                  Mass of Ball (B) = Mb  Initial velocity of mass A is…

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: Respond with TRUE if the symbol of the valve shown belows drawn correctly Select one True False

A: Solution:

Q: If gear 1 turns 620 degrees, how many degrees will gear 3 turn? N1 =20, N2

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.