C 3P; P; B 3V; A heat engine takes one mole of a diatomic ideal gas through the cycle illustrated in the figure above. If V, =5 m³ and P, = 1.54 10 Pa, answer the following questions. (R= 8.314 J-mol-1.K-1) a) Calculate the net work done through the cycle. Wnet = b) Find the total heat input for one complete cycle. Qin = J c) Find the total heat output for one complete cycle. Qout = d) Calculate the efficiency of the engine. Express your result as a percentage. e% = % e) What is the entropy change for process AB? ASAB ] J-K-1 f) What is the net entropy change for the whole cycle? ASnet ]J.K-1

C 3P; P; B 3V; A heat engine takes one mole of a diatomic ideal gas through the cycle illustrated in the figure above. If V, =5 m³ and P, = 1.54 10 Pa, answer the following questions. (R= 8.314 J-mol-1.K-1) a) Calculate the net work done through the cycle. Wnet = b) Find the total heat input for one complete cycle. Qin = J c) Find the total heat output for one complete cycle. Qout = d) Calculate the efficiency of the engine. Express your result as a percentage. e% = % e) What is the entropy change for process AB? ASAB ] J-K-1 f) What is the net entropy change for the whole cycle? ASnet ]J.K-1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a. What is the ideal mechanical advantage of this system? The inclined plane dimensions are 7.2 meters length and 1.8 meters height.b. What effort force is required to move the 600N create? c. In practice, you need to supply an effort force of 75 N to lift the crate. What is the efficiency?d. How could you redesign this compound machine so that the effort force needed was 50 N in practice? Assume the efficiency is your response from part C no matter what changes you make. Be specific with the changes you propose (if you add pulleys state how many, if you change the inclined plane dimensions state the new dimensions, etc.).
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
Discuss the concepts of perpetual-motion machines.
In a lathe machine, The diameter of the driver and driven pulley are 2745 mm and 1200 mm respectively, And the driver pulley runs at speed of 225 rpm. Find the speed at which is driven pulley runs in the machine. the speed of the driven pulley in rpm is
A machine with rational sections and subsystems is better than one that doesn't have either.
The process defined by the figure is characterized by: O Machining tolerance class up to IT8 O Greater material removal O Excellent surface finish
If a machine has a mechanical advantage of 4 and ideal mechanical advantage of 6, then its efficiency is about 0.70% 70% 1.5% 150%
Selasi wants a shaft of 5/8 inches diameter to be used in his design project of which he is considering a design factor of 3. He hopes to get the same shaft size or 11/16 inch diameter shaft in the market for his design. So he decided to send his apprentice, Amuzu to the market. Unfortunately, when Amuzu went to the market, there were 1⁄2 inch, 9/16 inch, 3⁄4 inch, and 7/8 inch sizes available in the first shop. Amuzu decided to buy the nearest shaft size in the first shop instead of checking in the other shops where he could have gotten either 5/8 inch or 11/16 inch sizes.a. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 9/16 inch size shaft. b. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 3⁄4 inch size shaft.
3
A CNC milling machine has a purchase price of £120,000 and it is considered from an accounting standpoint to be depreciated to zero value over a period of 5 years. If the machine is to be used for 2 shifts with each shift working for 37 hours/ week and 45 weeks/ year. What is the machine cost/ hr which must be charged in order to amortise/repay the costs over the 5 year period? To make the calculation simpler, you can assume that over the 5 year period you will be required to pay back 8% interest on the sum borrowed. Express your answer in § / hour rounded up to the nearest penny
I need accurate answer
This solution is incomplete. What about the answers to the following: d) Diameter of wheel in metres.e) Rotative speed in rpm if peripheral speed is 0.45√2gh.f) Specific speed of turbine in rpm.