By which type of a datum designer determine the reference point, line or surface for dimensioning? a)Design b)Assembly c)Production d)Auxiliary
Q: 4. Accuracy is often expressed as an average of several measurements. Look at the target to the…
A:
Q: Find the electric field at the origin if a 0.0002 C charge is placed 4.3 m directly above the origin…
A:
Q: Find the maximum charge a 46 V battery will put on a 72 mF capacitor in series with a 466 2…
A: Solution - Electric charge is the physical property of matter that causes it to experience a force…
Q: Which tool would be best to use for measuring the following: a) Diameter of a wire. Explain. b)…
A: a) A screw gauge would be better to measure the diameter of a wire because it's least count is…
Q: How many joules are required to heat 189 g of water from 7°C to 46°C? The specific heat for water is…
A:
Q: 1. What limitations are observed in making measurements using the: a. meter stick b. vernier caliper…
A: Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: A professional team of players is designing a catapult to launch a small ball at A so that it lands…
A:
Q: A BIG spool of copper wire has a resistance of 8 2 as measured from end of the wire to the other. If…
A: Given: Diameter of wire d=3 mm, Radius of wire r=d2=3 mm2=1.5 mm=1.5×10-3 m, Resistivity of wire…
Q: If you know x, a &t and want vo, which would be the best equation to use? A) x = vot + ½ at? B) v =…
A: Known quantities =x,a and tUnknown quantity=V0
Q: The area of a small rectangle is 418 mm-. Express this area in the S.I. unit. O a. 0.000418 square…
A:
Q: Find the mass of enough electrons to make up 7.3 C of charge. Each electron has a charge of…
A: It is given that, the mass of an electron is me=9.1×10-31 kg the charge stored in an electron is…
Q: wo straight, vertical wires X and Y pass through holes in a horizontal card. Fig. 8.1 shows the card…
A: Given: The current is flowing downward into the page in both the wire.
Q: 2. Sphere A has a charge of +10.0 C. It is brought in contact with a neutral sphere B and then…
A:
Q: What is the step by step procedure to solve any mesh analysis problem
A: Mesh analysis problem
Q: How many calibration does the device shown has ? A. One B. Two C. Three D. None
A: there are three calibrations a b -- to find diameter of a cylinders c d --- to find lengths of a…
Q: Explain in WORDS how you would teach someone to determine if their dimensional analysis answers make…
A: Dimensional analysis is a powerful tool used in science and engineering to check the validity of…
Q: Three point charges are arranged in an equilateral triangle with each side 5.0 cm long. Two of the…
A: Given that three point charges are arranged in equilateral triangle of side L=0.05m, the energy of…
Q: A systematic error 1. Ois also known as an indeterminate error 2. Ois a measure of the…
A: Error is defined as the difference between actual value & experimental value. It tells us…
Q: Suppose a distant world with surface gravity of 5.92 m/s2 has an atmospheric pressure of 8.84 x 10…
A: Acc. due to gravity = 5.92m/sec^2Radius r= 2mDepth h=10m
Q: A 54 mF capacitor is fully charged in a circuit with a 498 2 resistor and a 124 V battery. The…
A:
Q: The height, h, of two balls, in metres, after t seconds are shown in the graph below. b↑ 20 16 12 8…
A: The difference can be calculated by using the straight line drawn from one curve to another.
Q: R R2 B Ri
A: according to Kirchhoff's first law Algebraic sum of current at a junction is always zero.
Q: Find the direction of the electric field at the origin (at point (0,0)) if there are are two charges…
A:
Q: = 3. The emission spectrum of Hydrogen has a bright blue-green line at 486 nm. This electron ends in…
A:
Q: Find the magnitude of the electric field at the origin
A: Given: Charge q1=+4 mC located at point -2 m, 0 m Charge q2=+3 mC located at point 12 m, 0 m…
Q: 2. In each measurement below, write your reading with the proper number of significant figures and…
A:
Q: Find the Voltage needed to push 6 Amps of current through a 904 2 resistor. Your Answer:
A:
Q: A student measures the diameter (D) of a cylindrical wire using micrometer of accuracy (0.01mm) as…
A: A micrometer or a screw gauge is a device commonly used for the accurate measurements of components…
Q: 4 students measure the length of a nail and they obtained the following values: 2.34 cm, 2.33 cm,…
A: Precision Precision in measurements is indicate how close the measurement to each others. Accuracy…
Q: Using dimensional analysis, check which of the following equations is or are correct. 1. a=v/t 2.…
A: Given 1. a=v/t 2. density = mass/volume 3. speed = d/t^2 4. a=∆v/∆t
Q: If R1 = 250 ohms and R2 = 850 ohms, what is the smallest resistance you can get by combining both…
A: Given data: Two resistors R1 = 250 Ω and R2 = 850 Ω Required: The smallest resistance by combining…
Q: 3.Two particles A and B are released from rest, having equal charges of -8 x 10-6 C ad initially…
A: Given, Charge of each Particle (q1=q2)=-8×10-6 C Separation Distance between them (d)=0.025 m Mass…
Q: When what you are experimenting has 'far' results with the expected results as stated by the…
A: Reliability:- Reliability describes the closeness in the values of different measurements of the…
Q: Explain in WORDS how you would teach someone to determine if their dimensional analysis answer make…
A: Dimensional analysis is a powerful tool used to check the accuracy of mathematical equations and…
![](/static/compass_v2/shared-icons/check-mark.png)
Step by step
Solved in 2 steps
![Blurred answer](/static/compass_v2/solution-images/blurred-answer.jpg)