ans c please fast By using the Mohr's circle approach,c. Construct the Mohr's circle for the stress element shown in Figure Q1.d. Identify the following stresses and sketch the appropriate stress elementsrespectively.(1)Principal stresses and principal planes.(ii)Maximum shear stress and the corresponding normal stresse. Identify the state of stress when the element is rotated by an angle of 34°counterclockwise. Sketch the stress element after rotation. As a project engineer, you have been tasked to perform a stress analysis ofthe plane stresses of a stress element from the tie bar of a die castingmachine as shown in Figure Q1.60 MPa45 MPa.Figure Q1By using the stress transformation equations,a. By using the stress transformation equations, identify the state of stresswhen the element is rotated by an angle counterclockwise, where =0=92b. Identify the following stresses and sketch the appropriate stress elementsrespectively.(1)Principal stresses and principal planes.(ii)Maximum shear stress and the corresponding normal stress30 MPa

Givenσx=45MPaσy=-60MPaτ=30MPa

By using the Mohr's circle approach, c. Construct the Mohr's circle for the stress element shown in Figure Q1. d. Identify the following stresses and sketch the appropriate stress elements respectively. (i) Principal stresses and principal planes. (ii) Maximum shear stress and the corresponding normal stress

By using the Mohr's circle approach, c. Construct the Mohr's circle for the stress element shown in Figure Q1. d. Identify the following stresses and sketch the appropriate stress elements respectively. (i) Principal stresses and principal planes. (ii) Maximum shear stress and the corresponding normal stress

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices…

A: Identify the feature displayed in the picture, and choose from choices below.

Q: Need a front, top and side view of this please

A: This question is based on the concept of engineering drawing.

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: What type of scale is 1:20? O Full Scale O Enlargement Scale O Reduction Scale O O O

Q: Pls use any CAD software to draw the sectional view of the solid attached in the image below.

A: FindWe need to draw the sectional view of the given object using CAD software.

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Known values: L Rp Wdisk a disk 0.9 m 0.4 m 33° 30° 10 rad/s 10 rad/s? .2 Problem Statement: A disk…

A: Peg attachment mechanism:- In the case of spinal disc replacement options, we can conduct many…

Q: Determine the natural frequency of the system by a) the Equivalent Mass and Equivalent Stiffness…

A: (a) Write the expression of kinetic energy conservation to write equivalent mass of the system.…

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure To sketch the missing lines And hidden lines

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: What does SPC stand for?

A: SPC stands for statistical process control, which is the application of statistical instruments and…

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: Name the feature shown below.

A: The given figure is of

Question

ans c please fast

By using the Mohr's circle approach,
c. Construct the Mohr's circle for the stress element shown in Figure Q1.
d. Identify the following stresses and sketch the appropriate stress elements
respectively.
(1)
Principal stresses and principal planes.
(ii)
Maximum shear stress and the corresponding normal stress
e. Identify the state of stress when the element is rotated by an angle of 34°
counterclockwise. Sketch the stress element after rotation.

As a project engineer, you have been tasked to perform a stress analysis of
the plane stresses of a stress element from the tie bar of a die casting
machine as shown in Figure Q1.
60 MPa
45 MPa.
Figure Q1
By using the stress transformation equations,
a. By using the stress transformation equations, identify the state of stress
when the element is rotated by an angle counterclockwise, where =
0=92
b. Identify the following stresses and sketch the appropriate stress elements
respectively.
(1)
Principal stresses and principal planes.
(ii)
Maximum shear stress and the corresponding normal stress
30 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

NEED HELP WITH D THRUGH G
LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices below. Extrude Sketch Revolve Hole Pattern Create Form Press Pull Fillet Shell Combine Split Body Move Offset Plane Measure Canvas Select Windows Selection Crossing Selection Freeform Selection Paint Selection
LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices below. Extrude Sketch Revolve Hole Pattern Create Form Press Pull Fillet Shell Combine Split Body Move Offset Plane Measure Canvas Select Windows Selection Crossing Selection Freeform Selection Paint Selection
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
cant read and i think you need t solve for fn and ft