By using thecircuitgiven below;a) Find the total value of active power, reactivepowerapparent pawer, and powerfoctor of thesystem.b) Draw the r triengle,powerc) Find thecurrent drawn from the saurce.d) Find the equivalent impedonce that seenfrom theSource side.2000 VARCos Ø = 0,6(leading)SKVA2204250UFKosD=0,65(lagging)ohmSotHz

Answered: Image /qna-images/answer/0341d72e-4d59-49d8-8907-e13e19ccef2c.jpg

By using the circuit given belou; a) Find the total value of active power, reactive power apparent paver, and pawer factor b) Draw the power triangle, of the system. ) Find the. Current drawn from the saurce. d) Find the equi valent impadonce that seen from the Source side. 2000 VAR SKVA 2204 Cos0= 0,6 (leading) 250UF COSD=0,65 | Tagging) ohm SotHz

By using the circuit given belou; a) Find the total value of active power, reactive power apparent paver, and pawer factor b) Draw the power triangle, of the system. ) Find the. Current drawn from the saurce. d) Find the equi valent impadonce that seen from the Source side. 2000 VAR SKVA 2204 Cos0= 0,6 (leading) 250UF COSD=0,65 | Tagging) ohm SotHz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the boost converter shown. Switch Q is operating at 25 kHz with a duty cycle of 0.6. Assume the diode and switch to be ideal. Under steady-state condition, the average resistance R as seen by the source is (Round off to 2 decimal places.) £2. 15 V 1 mH voor Rin k ♫ ▷ 100 uF www 102
A. For the circuit diagram shown below, determine and sketch the output voltage (Vout). 1_ohm GaAs 1 ohm 1_ohm Ge Si A 1_ohm. 6_Vpeak w. Vout)
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
An RL load (R=0.2 Ohms, L=10 mH) is controlled by a converter. The supply voltage Vs is 600V and the chopper frequency is 200 Hz. The maximum peak to peak ripple current is equal to: Select one: a. 30A b. 55A c. 90A d. 75A
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
None
Design a CT-FWR to supply a load of (50) with a waveform of the following specifications: -  Vdc = 12 V  Ripple factor = 0.1 %  the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
a)circuit diagram with a load ,for the JFET. b)input and output waveform c)equations for the output ( v and i)
A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
3C) Calculate the values of the second harmonic (HD2) and third (HD3) as well as AUpzfor each of the circuits in the figure below. 3 Nout Nin 3
The waveform given below is observed on the screen of a CRO. If the time/div switch is set at 10 µsec and the volt/div at 200 mV, the frequency and peak to peak voltage are, respectively. -1.5 -1 -1- -2- 2 1 1 1.5 2