By applying a force F, a saline solution is ejected from the 10-mm-diameter syringe through a 0.4-mm-diameter needle. If the pressure developed within the syringe is 41 kPa, determine the average velocity(in m/s) of the solution through the needle. Take density of saline = 1,055 kg/m3 Answer in TWO(2) decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

By applying a force F, a saline solution is ejected from the 10-mm-diameter syringe through a 0.4-mm-diameter needle. If the pressure developed within the syringe is 41 kPa, determine the average velocity(in m/s) of the solution through the needle. Take density of saline = 1,055 kg/m3 Answer in TWO(2) decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

Name: By applying a force F, a saline solution is ejected from the 10-mm-di
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: By applying a force F, a saline solution is ejected from the 10-mm-diameter syringe through a 0.4-mm-diameter needle.If the pressure developed within the syringe is 41 kPa, determine the average velocity(in m/s) of the solution throughthe needle. Ta

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.87P: (a) Find the volume of liquid contained in the ï¬‚ask when it is filled to the full mark. (b)...

See similar textbooks

Similar questions

An aircraft is flying with a velocity of 207 m/s at a standard altitude where the temperature is 255 K. At a certain point on its wing, the local velocity is equal to the local speed of sound. Determine the pressure (Pascals) at that point. Round-off answer to the nearest whole number.
Find the discharge of water in liters / second in a pipe of diameter 20 cm with the velocity of 4.5 m/s. (ENTER ONLY THE VALUE IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET) The discharge of water through pipe is (Lit/sec) = Which of the following is the dimension of capillary depression O M'L1 T° O M° L' T° O M'L-1 TO M° L-2 TO The viscosity of Hydrogen gas increases when we heat it. Select one: O True O False
Water is flowing out of the nozzle (2) into atmospheric pressure (101 kPa). What is the flow velocity at point (1), when flow rate is 36.24 m3/h?
Determine the total summation of the y-component surface forces generated by the fluid in unit of lbf. Round to the nearest one decimal place. The average velocity vector and the absolute pressure of the section 1: V₁ = 4.3 i ft/s and P1 abs = 32 psi. The areas are A₁ = 15 in² and A2 = 3 in². The volume of the nozzle is 1.77 ft³. Ignore the weight of the nozzle.
5. Water is moving through a pipe. The velocity profile at some section is shown and is given mathematically as v = (B/4µ)(ď²/4 –P) where v = velocity of water at any position r, ß = a constant, µ is the viscosity of water, r= radial distance for centerline, d = pipe diameter,. What is the shear stress at the wall of the pipe from the water? What is the shear stress at a position r= d/4? If the profile above persists a distance L along with the pipe, what drag is induced on the pipe by the water in the direction of flow over this distance? -Velocity profile
Determine the critical velocity in m/s for Gasoline at 66°C flowing through a 46-mm pipe given that kinematic viscosity is 0.00044 m2/s; Round your answer to 3 decimal places.
A diverging tube discharges water from a reservoir at depth of 10m below the water surface. The diameter of the tube gradually increases from 150 mm at the throat to 225 mm at the outlet. Neglecting friction, determine the corresponding pressure, in kPa, at the throat. Round your answer to 2 decimal places. Water 10m
The pressure at the suction of the pump reads 6 psi vacuum, while at the discharge is 35 psi. The difference in elevation between the suction and discharge side is 2.3 ft. The diameter at suction is 6.7 in, while at the discharge is 4.9 in. Calculate the power delivered by the pump in hp if it delivers 1800 gpm. Write your answer to 1 decimal place.
To answer this question, first click here to view the associated video .Consider the flow of a viscous fluid through a pipe. Which of the following is true? The speed of the fluid is constant throughout the volume of the pipe. The speed of the fluid is greatest near the center of the pipe. The speed of the fluid is greatest near the walls of the pipe. A viscous fluid is flowing through two horizontal cylindrical pipes. The pressure difference P2-P1 between the ends of each pipe is the same. The pipes have the same radius, although one is twice as long as the other. How does the volume flow rate QB in the longer pipe compare to the volume flow rate QA in the shorter pipe? QA is the same as QB . QA is twice as large as QB . QA is one-fourth as large as QB . QA is half as large as QB .
Water flows through a horizontal pipe of cross section of 20cm2. At next section the cross sectional area is 4cm2. The pressure difference between the two sections is 29.4 psi. How many cubic meters of water will flow out of the pipe in 1.27 minute? Round your answer to 4 decimal places. Consider that this is a converging pipe.
Typewritten for an upvote. No upvote for handwritten. Please skip if you have already done this. Thank you
solve it fast