building construction. The beam is only reinforced with prestressing steel and no mild reinforcement is used. What is the maximum live load that this beam can carry (in addition to the self weight) considering only the allowable section stresses at Midspan? Blank 1 The material properties and prestressing are as follow:

building construction. The beam is only reinforced with prestressing steel and no mild reinforcement is used. What is the maximum live load that this beam can carry (in addition to the self weight) considering only the allowable section stresses at Midspan? Blank 1 The material properties and prestressing are as follow:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The T-beam has the following properties: flange thickness = 125 mm flange width = 1000 mm web width = 500 mm web height = 350 mm f'c = 28 Mpa a) Calculate the stresses in concrete at uncracked stage under 200 kN-m. b) Calculate the cracking moment. c) Determine the balanced steel area and balanced ultimate moment. The steel is placed 80 mm from its cg up to extreme fiber with yield strength of 414 MPa.
Problem 6: The wood beam is subjected to a load of 12 kN. Determine the transverse shear stress at point A is located 75 mm from the lower surface of the beam. Also what is the bending normal stress at A? 12 KN + 300 mm TH 200 mm -2 m---1 4.1 75 mol IM
Beam.flexural formula case.
R.Bars.
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
Problem Solving: A rectangular beam has dimensions of 250 mm by 625 mm with an effective depth (distance from extreme fiber in tension to the centroid of the reinforcing bars) of 575 mm and is reinforced with three 25 mmp. The concrete cylinder strength f.' = 27.6 MPa and the tensile strength in bending (modulus of rupture) is 3.28 MPa. The yield point of the steel is 414.7 MPa. The beam carries a bending moment of 61 kN.m. E_ = 200000 MPa. E_ = 4700,f. Using the transformed area method, determine the stress in the extreme fiber in compression.
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
Note: Read the question carefully and give me both right solutions with clear calculations. Don't copy from already available solutions.
A beam has a class 3 web and a class 2 flange. When along the stress-strain diagram will it fail, and how? Remember how we define the classes. Make a sketch showing a W-section beam that hasfailedin this way. How can this be prevented?
4
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =