3a) Calculate the moment producedF with respect to point B in Nm.Yanıt:3b) Determine the smallest force F in Newton applied to point C that produces the same amountof moment with respect to B.Yanıt3c) If you want to remove the nail by applying a vertical force P at point A. Calculate the magnitude of this vertical force P in Newton.Hint: The moment of this force is equal to the moment computed in part 3a.Yanıt:def hubyazın We know that to remove the nail at A from the board, we must apply a force F=148 N. which is applied with an angle B=17 degrees with respect to a horizontal axis.a=223 mm; L=0,7m. 8=48in degrees.BTFВa

For solution refer below images.

Answered: BT F a B.

Engineering

Mechanical Engineering

BT F a B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P17
3 kN/m. EN 8. A Draw Zm. TS.F. 9 B.M.)
Q.7 Degree of freedom at triple point is A В D -1
3. Determine the displacement of an eight-cylinder engine having a bore of 3.25 in and a stroke of 3 in.
Rod M,L ellle ellecl
There are four pulleys in each block of a set of rope pulley blocks. If the efficiency is 70% when lifting a load of 2.8 kN, what is the effort applied? А. 300N B. 200N C. 400N D. 500N
True or False 1. Small rubber gaskets are used to non isolate plates 2. Frames (gaskets) are suitable for all fluids 3. ACHE are comprised of multiple tubes through which liquid flows 4. To mix 3 kg of water at a temperature of 60 °C with 1 kg of water at a temperature of 35 °C, the temperature acquired by the water in the low-temperature container is not equal to the amount of heat lost from the first, due to the difference in the quantities of the two liquids
A D P L3 E B to L1 L2
iii. The piston rings. a. is used to withstand the pressure of gas in the cylinder b. acts as a bearing for the side thrust of the connecting rod C. is used to seal the cylinder in order to prevent leakage of the gas past the piston d. none of the above iv. For low speed engines, a rocker arm of.. . should be used a. rectangular section. b. 1 -section. c. T-section. d. circular. v. The most commonly used valve is the. . a. Rotary valve b. Poppet valve c. Disk valve d. one-piece design vi.-------- are caused by inertia effects of the rod mass. a. Tensile stresses b. Axial force c. Transverse forces d. Bending stresses vii. The connecting rod has two motions: ---(reciprocating, up -and- down) & ---- motion. viii. The gas pressure produces the following two types of stresses: (a) -, and (b)
6
Question 1) F=22 kN single load, M=24 kN.m moment and w=5 kN/m distributed load act on the beam whose loading condition is given in the figure. The length L is also given as L=4 m. The cross-sectional properties of the beam are; body height y g = 203 mm , body thickness x g = 19 mm, flange width x Question 1-E) Find the y distance of the section center with respect to the axis passing through the base of the section. ( Write your result in mm .) Question 1-F) section. (Do your operations by converting the lengths to meters. Take at least 4 digits for the decimal part of your result and use the expression E for the decimal part. Write it as 5E-3 instead of 0.005 .) f 172 mm , flange height yf = 16 mm. Point E on Find the moment of inertia of the beam the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the B level of the beam. According to this; D abutment response at point (D y Question 1-A) find. (Your result…
Identification1. It is a pair of equal, parallel and oppositely directed force.