Answered: (b)Sketch the waveforms of the gate…

(b)Sketch the waveforms of the gate drive voltages G1 and G2 assuming a duty cycle of 25% and a maximum gate drive voltage of 10V. How would you prevent the two MOSFET to turn on simultaneously.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
c) A buck converter with constant frequency peak current mode control has Vs = 28V, V = 20V, L = 301uH, fs = 100 kHz. Find the ramp slop for the optimum compensation and the peak compensation voltage. %3D
2. Given the circuit a. State how each switch can be realized using transistors and/or diodes, and whether the realization requires single-quadrant, current/voltage bi-directional two quadrant switch or four quadrant switches then redraw the circuit. b. Solve the converter to determine the inductor currents, capacitor voltages and conversion ratio. Ignore all losses.
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
B7
A single-phase full bridge uncontrolled rectifier is supplied by 220 V (rms) line voltage. The load is pure resistive. What is the output Ripple Factor ?
Please written by computer Answer the following questions:a. Name a suitable topology that can be used in the above DC/DC converters to achieve the required regulation with the minimum provided efficiency.b. Calculate the efficiency of the linear regulator.c. Calculate the total input power and the input current.d. Calculate the overall efficiency of the system.e. If a 100uF capacitor is used at the input to minimize the ripple. Assume the rise time of the input source is 0.2ms. Estimate the maximum inrush current to charge the capacitor to 12V.
Derive the average and RMS output voltage for three phase half controlled rectifier with RLE Load or three phase semi converters.
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?